SNOS641F – OCTOBER 1999 – REVISED JULY 2013
LM4041-N/LM4041-N-Q1 ADJ (Adjustable) Electrical Characteristics (Industrial Temperature
Range)
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
;
all other limits T
J
= 25°C unless otherwise specified (SOT-23, see
(1)
),
I
RMIN
≤
I
R
≤
12 mA, V
REF
≤
V
OUT
≤
10V. The grades C and D designate initial Reference Voltage Tolerances of ±0.5% and
±1%, respectively for V
OUT
= 5V.
Symbol
Parameter
Conditions
Typical
(2)
LM4041CIM3
LM4041QCIM3
LM4041CIZ
LM4041CIM7
(3)
LM4041DIM3
LM4041QDIM3
LM4041DIZ
LM4041DIM7
(3)
Units
(Limit)
V
REF
Reference Voltage
Reference Voltage
Tolerance
(4)
I
R
= 100
μA,
V
OUT
= 5V
I
R
= 100
μA,
V
OUT
= 5V
1.233
±6.2
±14
45
60
65
65
70
2.0
2.5
6
8
−2.5
−3.0
150
200
±150
±12
±24
V
mV (max)
mV (max)
μA
μA
(max)
μA
(max)
mV
1.5
2.0
mV (max)
mV (max)
mV
4
6
mV (max)
mV (max)
mV/V
−2.0
−2.5
mV/V (max)
mV/V (max)
nA
100
120
nA (max)
nA (max)
ppm/°C
±100
ppm/°C (max)
ppm/°C
I
RMIN
Minimum Operating
Current
ΔV
REF
/ΔI
R
Reference Voltage
Change with Operating
Current Change
(5)
I
RMIN
≤
I
R
≤
1 mA
SOT-23: V
OUT
≥
1.6V
(6)
0.7
1 mA
≤
I
R
≤
12 mA
SOT-23: V
OUT
≥
1.6V
(6)
2
ΔV
REF
/ΔV
O
Reference Voltage
Change with Output
Voltage Change
Feedback Current
I
R
= 1 mA
−1.55
I
FB
60
ΔV
REF
/ΔT
Average Reference
Voltage Temperature
Coefficient
(4)
Dynamic Output
Impedance
V
OUT
=
5V,
I
R
= 10 mA
I
R
=
1 mA
I
R
= 100
μA
20
15
15
Z
OUT
I
R
= 1 mA, f = 120 Hz,
I
AC
= 0.1 I
R
V
OUT
= V
REF
V
OUT
= 10V
0.3
2
20
Ω
Ω
μV
rms
e
N
Wideband Noise
I
R
= 100
μA
V
OUT
= V
REF
10 Hz
≤
f
≤
10 kHz
ΔV
REF
V
HYST
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Reference Voltage Long
Term Stability
Thermal Hysteresis
(7)
t = 1000 hrs, I
R
= 100
μA,
T = 25°C ±0.1°C
ΔT
=
−40°C
to +125°C
120
0.08
ppm
%
When V
OUT
≤
1.6V, the LM4041-N ADJ in the SOT-23 package must operate at reduced I
R
. This is caused by the series resistance of
the die attach between the die (-) output and the package (-) output pin. See the
curve in the
section.
Typicals are at T
J
= 25°C and represent most likely parametric norm.
Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
Reference voltage and temperature coefficient will change with output voltage. See
curves.
Load regulation is measured on pulse basis from no load to the specified load current. Ouput changes due to die temperature change
must be taken into account separately.-
When V
OUT
≤
1.6V, the LM4041-N ADJ in the SOT-23 package must operate at reduced I
R
. This is caused by the series resistance of
the die attach between the die (-) output and the package (-) output pin. See the
curve in the
section.
Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
Copyright © 1999–2013, Texas Instruments Incorporated
7
Product Folder Links:
TI [ TEXAS INSTRUMENTS ]
