LM4040-N, LM4040Q-N
SNOS633H –OCTOBER 2000–REVISED APRIL 2013
www.ti.com
10.0-V LM4040-N Electrical Characteristics
VR Tolerance Grades 'C' and 'D'; Temperature Grade 'I'
Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C. The grades C and D designate initial
Reverse Breakdown Voltage tolerances of ±0.5% and ±1.0%, respectively.
LM4040CIM3
LM4040CIZ
Limits(2)
LM4040DIM3
LM4040DIZ
Limits(2)
Symbol
VR
Parameter
Conditions
Typical(1)
Units
Reverse Breakdown Voltage
IR = 150 μA
10.00
V
mV (max)
mV (max)
μA
±50
±100
Reverse Breakdown Voltage
Tolerance(3)
IR = 150 μA
±115
±198
75
IRMIN
Minimum Operating Current
100
110
μA (max)
μA (max)
ppm/°C
ppm/°C (max)
ppm/°C
mV
103
113
IR = 10 mA
IR = 1 mA
±40
±20
±20
0.8
Average Reverse Breakdown
ΔVR/ΔT Voltage Temperature
±100
±150
Coefficient(3)
IR = 150 μA
IRMIN ≤ IR ≤ 1 mA
1.5
2.0
mV (max)
mV (max)
mV
Reverse Breakdown Voltage
3.5
4.0
ΔVR/ΔIR Change with Operating
Current Change(4)
8.0
1 mA ≤ IR ≤ 15 mA
12.0
18.0
mV (max)
mV (max)
Ω
23.0
29.0
0.7
IR = 1 mA, f = 120 Hz,
IAC = 0.1 IR
ZR
eN
Reverse Dynamic Impedance
Wideband Noise
1.7
2.3
Ω (max)
IR = 150 μA
10 Hz ≤ f ≤ 10 kHz
180
μVrms
t = 1000 hrs
T = 25°C ±0.1°C
IR = 150 μA
Reverse Breakdown Voltage
Long Term Stability
ΔVR
120
ppm
%
VHYST
Thermal Hysteresis(5)
ΔT = −40°C to +125°C
0.08
(1) Typicals are at TJ = 25°C and represent most likely parametric norm.
(2) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(3) The boldface (over-temperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse
Breakdown Voltage Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum
difference in temperature from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total over-
temperature tolerance for the different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total over-temperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown
below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an over-temperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
22
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM4040-N LM4040Q-N