SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013
ELECTRICAL CHARACTERISTICS (continued)
V
+
= +5.0V, See
, unless otherwise stated
Parameter
Output Current
+
Conditions
Source V
IN
= +1V, V
IN
= 0V,
V
+
= 15V, V
O
= 2V
Sink V
IN
−
= +1V, V
IN+
= 0V,
V
+
= 15V, V
O
= 2V
−
LM158A
Min
10
10
Typ
20
15
Max
Min
10
5
LM358A
Typ
20
8
Max
LM158/LM258
Min
10
5
Typ
20
8
Max
Units
mA
mA
ELECTRICAL CHARACTERISTICS
V
+
= +5.0V, See
(1)
, unless otherwise stated
Parameter
Large Signal Voltage
Gain
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
Amplifier-to-Amplifier Coupling
Output Current
Conditions
V
+
= 15V, T
A
= 25°C,
R
L
≥
2 kΩ, (For V
O
= 1V to 11V)
T
A
= 25°C,
V
CM
= 0V to V
+
−1.5V
V
+
= 5V to 30V
(LM2904, V
+
= 5V to 26V), T
A
= 25°C
f = 1 kHz to 20 kHz, T
A
= 25°C
(Input Referred), See
(2)
V
IN
−
= 0V,
V
+
= 15V,
V
O
= 2V, T
A
= 25°C
Sink V
IN
−
= 1V, V
IN+
= 0V
V
+
= 15V, T
A
= 25°C,
V
O
= 2V
V
IN
−
= 1V,
V
IN+
= 0V
T
A
= 25°C, V
O
= 200 mV,
V
+
= 15V
Short Circuit to Ground
Input Offset Voltage
Input Offset Voltage Drift
Input Offset Current
Input Offset Current Drift
Input Bias Current
Input Common-Mode
Voltage Range
(1)
(2)
(3)
T
A
= 25°C, See
(3)
, V
+
= 15V
See
(4)
LM358
Min
25
65
65
Typ
100
85
100
Max
Min
25
50
50
LM2904
Typ
100
70
100
Max
Units
V/mV
dB
dB
−120
−120
dB
Source V
IN+
= 1V,
20
40
20
40
mA
10
20
10
20
mA
12
50
12
50
μA
40
7
60
9
40
7
60
10
mA
mV
μV/°C
nA
pA/°C
nA
V
R
S
= 0Ω
I
IN(+)
−
I
IN(−)
R
S
= 0Ω
I
IN(+)
or I
IN(−)
V
+
= 30 V, See
(5)
(LM2904, V
+
= 26V)
0
150
10
40
500
V
+
−2
0
45
10
40
200
500
V
+
−2
(4)
(5)
These specifications are limited to
−55°C ≤
T
A
≤
+125°C for the LM158/LM158A. With the LM258/LM258A, all temperature
specifications are limited to
−25°C ≤
T
A
≤
+85°C, the LM358/LM358A temperature specifications are limited to 0°C
≤
T
A
≤
+70°C, and
the LM2904 specifications are limited to
−40°C ≤
T
A
≤
+85°C.
Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
Short circuits from the output to V
+
can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V
+
. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
V
O
≃
1.4V, R
S
= 0Ω with V
+
from 5V to 30V; and over the full input common-mode range (0V to V
+
−1.5V)
at 25°C. For LM2904, V
+
from
5V to 26V.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V
+
−1.5V
(at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V
+
.
Copyright © 2000–2013, Texas Instruments Incorporated
6
Product Folder Links:
TI [ TEXAS INSTRUMENTS ]
