LM2675
www.ti.com
SNVS129E –MAY 2004–REVISED JUNE 2005
LM2675 Series Buck Regulator Design Procedure (Adjustable Output)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
To simplify the buck regulator design procedure, Texas Instruments
is making available computer design software to be used with the
SIMPLE SWITCHER line of switching regulators.LM267X Made
Simpleversion 6.0 is available for use on Windows®3.1, NT, or 95
operating systems.
Given:
Given:
•
•
•
•
VOUT = Regulated Output Voltage
VIN(max) = Maximum Input Voltage
ILOAD(max) = Maximum Load Current
F = Switching Frequency (Fixed at a nominal 260 • F = Switching Frequency (Fixed at a nominal 260
kHz). kHz).
•
•
•
VOUT = 20V
VIN(max) = 28V
ILOAD(max) = 1A
1. Programming Output Voltage (Selecting R1 and R2, as shown in 1. Programming Output Voltage (Selecting R1 and R2, as shown in
Figure 23)
Figure 23)
Use the following formula to select the appropriate resistor values.
Select R1 to be 1 kΩ, 1%. Solve for R2.
where VREF = 1.21V
Select a value for R1 between 240Ω and 1.5 kΩ. The lower resistor
R2 = 1k (16.53 − 1) = 15.53 kΩ, closest 1% value is 15.4 kΩ.
values minimize noise pickup in the sensitive feedback pin. (For the R2 = 15.4 kΩ.
lowest temperature coefficient and the best stability with time, use
1% metal film resistors.)
2. Inductor Selection (L1)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant E • T (V • μs), A. Calculate the inductor Volt • microsecond constant (E • T),
from the following formula:
where
•
VSAT = internal switch saturation voltage =
0.25V
•
VD = diode forward voltage drop = 0.5V
B. Use the E • T value from the previous formula and match it with
the E • T number on the vertical axis of the Inductor Value Selection
Guide shown in Figure 27.
B. E • T = 21.6 (V • μs)
C. ILOAD(max) = 1A
C. On the horizontal axis, select the maximum load current.
D. Identify the inductance region intersected by the E • T value and
the Maximum Load Current value. Each region is identified by an
inductance value and an inductor code (LXX).
D. From the inductor value selection guide shown in Figure 27, the
inductance region intersected by the 21.6 (V • μs) horizontal line and
the 1A vertical line is 68 μH, and the inductor code is L30.
E. Select an appropriate inductor from the four manufacturer's part
numbers listed in Table 1. For information on the different types of
inductors, see the inductor selection in the fixed output voltage
design procedure.
E. From the table in Table 1, locate line L30, and select an inductor
part number from the list of manufacturers part numbers.
3. Output Capacitor Selection (COUT
)
3. Output Capacitor SeIection (COUT)
A. Select an output capacitor from the capacitor code selection guide A. Use the appropriate row of the capacitor code selection guide, in
in Table 9. Using the inductance value found in the inductor
selection guide, step 1, locate the appropriate capacitor code
corresponding to the desired output voltage.
Table 9. For this example, use the 15–20V row. The capacitor code
corresponding to an inductance of 68 μH is C20.
Copyright © 2004–2005, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM2675