bq24070
bq24071
www.ti.com
SLUS694B–MARCH 2006–REVISED AUGUST 2006
FUNCTIONAL DESCRIPTIONS (continued)
1. This feature allows the designer to select a lower power wall adapter, if the average system load is
moderate compared to its peak power. For example, if the peak system load is 1.75 A, average system load
is 0.5 A and battery fast-charge current is 1.25 A, the total peak demand could be 3 A. With DPPM, a 2-A
adaptor could be selected instead of a 3.25-A supply. During the system peak load of 1.75 A and charge
load of 1.25 A, the smaller adaptor’s voltage drops until the output voltage reaches the DPPM regulation
voltage threshold. The charge current is reduced until there is no further drop on the output voltage. The
system gets its 1.75-A charge and the battery charge current is reduced from 1.25 A to 0.25 A. When the
peak system load drops to 0.5 A, the charge current returns to 1 A and the output voltage returns to its
normal value.
2. Using DPPM provides a power savings compared to configurations without DPPM. Without DPPM, if the
system current plus charge current exceed the supply’s current limit, then the output is pulled down to the
battery. Linear chargers dissipate the unused power (VIN-VOUT) × ILOAD. The current remains high (at current
limit) and the voltage drop is large for maximum power dissipation. With DPPM, the voltage drop is less
(VIN-V(DPPM-REG)) to the system which means better efficiency. The efficiency for charging the battery is the
same for both cases. The advantages include less power dissipation, lower system temperature, and better
overall efficiency.
3. The DPPM sustains the system voltage no matter what causes it to drop, if at all possible. It does this by
reducing the noncritical charging load while maintaining the maximum power output of the adaptor.
Note that the DPPM voltage, V(DPPM), is programmed as follows:
V
+ I
R
SF
(DPPM−REG)
(DPPM)
(DPPM)
(1)
where
R(DPPM) is the external resistor connected between the DPPM and VSS pins.
I(DPPM) is the internal current source.
SF is the scale factor as specified in the specification table.
The safety timer is dynamically adjusted while in DPPM mode. The voltage on the ISET1 pin is directly
proportional to the programmed charging current. When the programmed charging current is reduced, due to
DPPM, the ISET1 and TMR voltages are reduced and the timer’s clock is proportionally slowed, extending the
safety time. In normal operation V(TMR) = 2.5 V; and, when the clock is slowed, V(TMR) is reduced. When
V(TMR) = 1.25 V, the safety timer has a value close to 2 times the normal operation timer value. See Figure 5
through Figure 6.
Case 2: USB Mode (Mode = L)
System Power
In this case, the system load is powered from a USB port through the internal switch Q1 (see Figure 4). Note
that in this case, Q1 regulates the total current to the 100-mA or 500-mA level, as selected on the ISET2 input.
The output, VOUT, is regulated to 4.4 V (bq24070). The system's power management is responsible for keeping
its system load below the USB current level selected (if the battery is critically low or missing). Otherwise, the
output drops to the battey voltage; therefore, the system should have a low-power mode for USB power
application. The DPPM feature keeps the output from dropping below its programmed threshold, due to the
battery charging current, by reducing the charging current.
Charge Control
When in USB mode, Q1 regulates the input current to the value selected by the ISET2 pin (0.1/0.5 A). The
charge current to the battery is set by the ISET1 resistor (typically > 0.5 A). Because the charge current typically
is programmed for more current than the USB current limit allows, the output voltage drops to the battery voltage
or DPPM voltage, whichever is higher. If the DPPM threshold is reached first, the charge current is reduced until
VOUT stops dropping. If VOUT drops to the battery voltage, the battery is able to supplement the input current to
the system.
13
Submit Documentation Feedback
TI [ TEXAS INSTRUMENTS ]
