bq24010, bq24012
bq24013, bq24014, bq24018
SLUS530K – SEPTEMBER 2002 – REVISED JANUARY 2014
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS
(1)
VALUE
Supply voltage range, (V
CC
all with respect to V
SS
)
Input voltage range
(2)
IN, STAT1, STAT2, TS, PG, CE, TTE
BAT, OUT, ISET
STAT1, STAT2, PG
IN, OUT
–0.3 to 18
–0.3 to VCC
–0.3 to 7
±0.5
15
1.5
–40 to 125
–65 to 150
°C
°C
UNIT
V
V
VDC
V
Voltage difference between V
CC
and IN inputs V
CC
– V
IN
Output sink/source current
Output current
T
A
T
J
T
stg
(1)
(2)
Junction temperature range
Storage temperature
Operating free-air temperature range
Stresses beyond those listed under
absolute maximum ratings
may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under
recommended operating
conditions
is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are DC and with respect to VSS.
DISSIPATION RATINGS
PACKAGE
DRC
(1)
(1)
θ
JA
47°C/W
T
A
< 40°C
POWER RATING
1.5 W
DERATING FACTOR
ABOVE T
A
= 40°C
0.021 W/°C1
This data is based on using the JEDEC High-K board and the exposed die pad is connected to a copper pad on the board. This is
connected to the ground plane by a 2x3 via matrix.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
V
CC
V
IN
T
J
(1)
(2)
Supply voltage
Input voltage
(1) (2)
NOM
MAX
16.5
16.5
125
UNIT
V
V
°C
3
3
–40
(1) (2)
Operating junction temperature range
Pins V
CC
and IN must be tied together.
If Vin is between UVLO and 4.35V, and above the battery voltage, then the IC is active (can deliver some charge to the battery), but the
IC will have limited or degraded performance (some functions may not meet data sheet specifications). The battery may be
undercharged (V
O(reg)
less than in the specification), but will not be overcharged (V
O(reg)
will not exceed specification).
ELECTRICAL CHARACTERISTICS
over 0°C
≤
T
J
≤
125°C and recommended supply voltage, (unless otherwise noted)
PARAMETER
INPUT CURRENT
I
CC(VCC)
I
CC(SLP)
I
IB(BAT)
I
IB(TS)
I
IB(CE)
I
IB(TTE)
VCC current
Sleep current
Input bias current on BAT pin
Input current on TS pin
Input current on CE pin
Input bias current on TTE pin
V
I(TS)
≤
10 V
V
CC
> V
CC(min)
, STATx pins in OFF state
Sum of currents into OUT and BAT pins, V
CC
< V
(SLP)
0
3.5
5
5
500
1
1
1
μA
mA
μA
nA
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VOLTAGE REGULATION V
O(REG)
+ V
(DO–MAX)
≤
V
CC
, I
(TERM)
< I
O(OUT)
≤
1 A
Output voltage, V
O(REG)
bq24010, bq24012, bq24013, bq24014
bq24018
4.2
4.36
V
2
Submit Documentation Feedback
Copyright © 2002–2014, Texas Instruments Incorporated
Product Folder Links:
bq24010, bq24012 bq24013, bq24014, bq24018
TI [ TEXAS INSTRUMENTS ]
