78P2351R
Serial 155M
NRZ to CMI Converter
Synchronous Mode
TRANSMITTER OPERATION
When the NRZ transmit data is source synchronous
with the reference clock applied at CKREFP/N as
shown in Figure 2, the 78P2351R can be optionally
used in synchronous mode or re-timing mode. In
this mode, the 78P2351R will recover the clock from
the NRZ data input and re-time the data in an
integrated +/- 4-bit FIFO.
The transmitter section generates an adjustable
ITU-T G.703 compliant analog signal for
transmission through a wideband transformer onto
75Ω coaxial cable. Differential NRZ data is input to
the 78P2351R on the SIDP/N pins at LVPECL levels
and passed to a low jitter clock and data recovery
circuit.
An optional clock decoupling FIFO is
System Reference Clock
provided to decouple the on chip and off chip clocks.
The NRZ data is encoded using CMI line coding to
ensure an adequate number of transitions.
CKREFP/N
NRZ
NRZ
CMI
CMI
Coax
Coax
CMIP/N
RXP/N
XFMR
XFMR
SIDP/N
Framer/
Mapper
TDK
Each of the transmit timing modes can be configured
in HW mode or SW mode as shown in the table
below.
78P2351R
SODP/N
HW Control
CKMODE
SW Control
SMOD[1:0]
Tx Mode
Figure 2: Synchronous
Since the reference clock and transmit clock/data go
through different delay paths, it is inevitable that the
phase relationship between the two clocks can vary
in a bounded manner due to the fact that the
absolute delays in the two paths can vary over time.
The transmit FIFO allows long-term clock phase drift
between the Tx clock and system reference clock,
not exceeding +/- 25.6ns, to be handled without
transmit error. If the clock wander exceeds the
specified limits, the FIFO will over or under flow, and
the FERR register signal will be asserted. This
signal can be used to trigger an interrupt. This
interrupt event is automatically cleared when a FIFO
Reset (FRST) pulse is applied, and the FIFO is re-
centered.
Reserved
Low
0 0
1 0
Synchronous
Floating
(FIFO enabled)
Plesiochronous
Loop-timing
High
n/a
0 1
1 1
Plesiochronous Mode
Plesiochronous mode represents
a
common
condition where a synchronous reference clock is
not available. In this mode, the 78P2351R will
recover the transmit clock from the plesiochronous
data and bypass the internal FIFO and re-timing
block. This mode is commonly used for mezzanine
cards, modules, and any application where the
reference clock can’t always be synchronous to the
transmit source clock/data
Notes:
1) External remote loopbacks (i.e. loopback
within framer) are not possible in
synchronous operation (FIFO enabled)
unless the data is re-justified to be
synchronous to the system reference clock
or the 78P2351R is configured for loop-
timing operation.
2) During IC power-up or transmit power-up,
the clocks going to the FIFO may not be
stable and cause the FIFO to overflow or
underflow. As such, the FIFO should be
manually reset using FRST anytime the
transmitter is powered-up.
System
Clock
XO
CKREFP
NRZ
NRZ
CMI
CMI
Coax
Coax
CMIP/N
RXP/N
XFMR
XFMR
SIDP/N
Framer/
Mapper
TDK
78P2351R
SODP/N
Figure 1: Plesiochronous Mode
Clock Synthesizer
The transmit clock synthesizer is a low-jitter PLL that
generates a 311.04 MHz clock for the CMI encoder.
A synthesized 155.52 MHz reference clock is also
used in both the receive and transmit sides for clock
and data recovery.
Page: 5 of 31
2006 Teridian Semiconductor Corporation
Rev. 2.1