欢迎访问ic37.com |
会员登录 免费注册
发布采购

73S1217F-IMR/F 参数 Datasheet PDF下载

73S1217F-IMR/F图片预览
型号: 73S1217F-IMR/F
PDF下载: 下载PDF文件 查看货源
内容描述: 总线供电80515的系统级芯片, USB , ISO 7816 / EMV ,密码键盘和更多 [Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More]
分类和应用: 多功能外围设备微控制器和处理器时钟
文件页数/大小: 140 页 / 1066 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号73S1217F-IMR/F的Datasheet PDF文件第43页浏览型号73S1217F-IMR/F的Datasheet PDF文件第44页浏览型号73S1217F-IMR/F的Datasheet PDF文件第45页浏览型号73S1217F-IMR/F的Datasheet PDF文件第46页浏览型号73S1217F-IMR/F的Datasheet PDF文件第48页浏览型号73S1217F-IMR/F的Datasheet PDF文件第49页浏览型号73S1217F-IMR/F的Datasheet PDF文件第50页浏览型号73S1217F-IMR/F的Datasheet PDF文件第51页  
DS_1217F_002  
73S1217F Data Sheet  
1.7.7 Timers and Counters  
The 80515 has two 16-bit timer/counter registers: Timer 0 and Timer 1. These registers can be  
configured for counter or timer operations.  
In timer mode, the register is incremented every machine cycle, meaning that it counts up after every 12  
periods of the MPU clock signal.  
In counter mode, the register is incremented when the falling edge is observed at the corresponding input  
signal T0 or T1 (T0 and T1 are the timer gating inputs derived from USR[0:7] pins, see the User (USR)  
Ports section). Since it takes 2 machine cycles to recognize a 1-to-0 event, the maximum input count  
rate is 1/2 of the oscillator frequency. There are no restrictions on the duty cycle, however to ensure  
proper recognition of 0 or 1 state, an input should be stable for at least 1 machine cycle.  
Four operating modes can be selected for Timer 0 and Timer 1. Two Special Function Registers (TMOD  
and TCON) are used to select the appropriate mode.  
The Timer 0 load registers are designated as TL0 and TH0 and the Timer 1 load registers are designated  
as TL1 and TH1.  
Timer/Counter Mode Control Register (TMOD): 0x89 Å 0x00  
Table 40: The TMOD Register  
MSB  
GATE  
LSB  
M0  
C/T  
M1  
M0  
GATE  
C/T  
M1  
Timer 1  
Timer 0  
Bits TR1 and TR0 in the TCON register start their associated timers when set.  
Bit  
Symbol  
Function  
TMOD.7  
TMOD.3  
GATE  
If set, enables external gate control (USR pin(s) connected to T0 or T1  
for Counter 0 or 1, respectively). When T0 or T1 is high, and TRx bit is  
set (see the TCON register), a counter is incremented every falling edge  
on T0 or T1 input pin. If not set, the TRx bit controls the corresponding  
timer.  
TMOD.6  
TMOD.2  
C/T  
Selects Timer or Counter operation. When set to 1, the counter  
operation is performed based on the falling edge of T0 or T1. When  
cleared to 0, the corresponding register will function as a timer.  
TMOD.5  
TMOD.1  
M1  
M0  
Selects the mode for Timer/Counter 0 or Timer/Counter 1, as shown in  
TMOD description.  
TMOD.4  
TMOD.0  
Selects the mode for Timer/Counter 0 or Timer/Counter 1, as shown in  
TMOD description.  
Rev. 1.2  
47  
 
 复制成功!