欢迎访问ic37.com |
会员登录 免费注册
发布采购

73S1217F-IMR/F 参数 Datasheet PDF下载

73S1217F-IMR/F图片预览
型号: 73S1217F-IMR/F
PDF下载: 下载PDF文件 查看货源
内容描述: 总线供电80515的系统级芯片, USB , ISO 7816 / EMV ,密码键盘和更多 [Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More]
分类和应用: 多功能外围设备微控制器和处理器时钟
文件页数/大小: 140 页 / 1066 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号73S1217F-IMR/F的Datasheet PDF文件第32页浏览型号73S1217F-IMR/F的Datasheet PDF文件第33页浏览型号73S1217F-IMR/F的Datasheet PDF文件第34页浏览型号73S1217F-IMR/F的Datasheet PDF文件第35页浏览型号73S1217F-IMR/F的Datasheet PDF文件第37页浏览型号73S1217F-IMR/F的Datasheet PDF文件第38页浏览型号73S1217F-IMR/F的Datasheet PDF文件第39页浏览型号73S1217F-IMR/F的Datasheet PDF文件第40页  
73S1217F Data Sheet  
1.7.5.1 Interrupt Overview  
DS_1217F_002  
When an interrupt occurs, the MPU will vector to the predetermined address as shown in Table 32. Once  
the interrupt service has begun, it can only be interrupted by a higher priority interrupt. The interrupt  
service is terminated by a return from the RETI instruction. When an RETI is performed, the processor  
will return to the instruction that would have been next when the interrupt occurred.  
When the interrupt condition occurs, the processor will also indicate this by setting a flag bit. This bit is  
set regardless of whether the interrupt is enabled or disabled. Each interrupt flag is sampled once per  
machine cycle, then samples are polled by the hardware. If the sample indicates a pending interrupt  
when the interrupt is enabled, then the interrupt request flag is set. On the next instruction cycle, the  
interrupt will be acknowledged by hardware forcing an LCALL to the appropriate vector address.  
Interrupt response will require a varying amount of time depending on the state of the MPU when the  
interrupt occurs. If the MPU is performing an interrupt service with equal or greater priority, the new  
interrupt will not be invoked. In other cases, the response time depends on the current instruction. The  
fastest possible response to an interrupt is 7 machine cycles. This includes one machine cycle for  
detecting the interrupt and six cycles to perform the LCALL.  
1.7.5.2  
Special Function Registers for Interrupts  
Interrupt Enable 0 Register (IEN0): 0xA8 Å 0x00  
Table 19: The IEN0 Register  
MSB  
EAL  
LSB  
EX0  
WDT  
ES0  
ET1  
EX1  
ET0  
Bit  
Symbol  
EAL  
WDT  
Function  
IEN0.7  
IEN0.6  
IEN0.5  
IEN0.4  
IEN0.3  
IEN0.2  
IEN0.1  
IEN0.0  
EAL = 0 – disable all interrupts.  
Not used for interrupt control.  
ES0  
ET1  
EX1  
ET0  
EX0  
ES0 = 0 – disable serial channel 0 interrupt.  
ET1 = 0 – disable timer 1 overflow interrupt.  
EX1 = 0 – disable external interrupt 1.  
ET0 = 0 – disable timer 0 overflow interrupt.  
EX0 = 0 – disable external interrupt 0.  
36  
Rev. 1.2  
 
 复制成功!