欢迎访问ic37.com |
会员登录 免费注册
发布采购

71M6533-IGTR/F 参数 Datasheet PDF下载

71M6533-IGTR/F图片预览
型号: 71M6533-IGTR/F
PDF下载: 下载PDF文件 查看货源
内容描述: 电能计量IC [Energy Meter IC]
分类和应用: 模拟IC信号电路
文件页数/大小: 124 页 / 1997 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号71M6533-IGTR/F的Datasheet PDF文件第115页浏览型号71M6533-IGTR/F的Datasheet PDF文件第116页浏览型号71M6533-IGTR/F的Datasheet PDF文件第117页浏览型号71M6533-IGTR/F的Datasheet PDF文件第118页浏览型号71M6533-IGTR/F的Datasheet PDF文件第120页浏览型号71M6533-IGTR/F的Datasheet PDF文件第121页浏览型号71M6533-IGTR/F的Datasheet PDF文件第122页浏览型号71M6533-IGTR/F的Datasheet PDF文件第123页  
FDS_6533_6534_004  
71M6533/71M6534 Data Sheet  
Name  
Type Cicuit Description  
E_RXTX/SEG9  
E_RST/SEG11  
E_TCLK/SEG10  
ICE_E  
I/O  
I/O  
O
1, 4, 5 Multi-use pins, configurable as either emulator port pins (when  
ICE_E pulled high) or LCD SEG drivers (when ICE_E tied to GND).  
1, 4, 5  
4, 5  
2
I
ICE enable. When zero, E_RST, E_TCLK, and E_RXTX become  
SEG9, SEG10, and SEG11 respectively. For production units, this  
pin should be pulled to GND to disable the emulator port.  
CKTEST/SEG19,  
MUXSYNC/SEG7  
O
4, 5  
Multi-use pins, configurable as either multiplexer/clock output or  
LCD segment driver using the I/O RAM registers CKOUT_E or  
MUX_SYNC_E.  
TMUXOUT  
O
4
Pin connected to the output test multiplexer. Controlled by  
TMUX[3:0].  
OPT_RX/DIO1  
I/O  
3, 4  
Multi-use pin, configurable as Optical Receive Input or general DIO.  
When configured as OPT_RX, this pin is a regular UART RX pin.  
If this pin is unused it must be configured as an output or termi-  
nated to V3P3D or GNDD.  
OPT_TX/DIO2  
RESET  
I/O  
I
3, 4  
2
Multi-use pin, configurable as either Optical LED Transmit Output  
or general DIO. When configured as OPT_TX, this pin is capable  
of directly driving an LED for transmitting data in an IR serial inter-  
face.  
Chip reset: This input pin is used to reset the chip into a known  
state. For normal operation, this pin is pulled low. To reset the  
chip, this pin should be pulled high. This pin has an internal 30 μA  
(nominal) current source pull-down. No external reset circuitry is  
necessary.  
RX  
I
3
UART input. If this pin is unused it must be terminated to  
V3P3D or GNDD.  
TX  
TEST  
O
I
4
7
UART output.  
Enables Production Test.  
This pin must be grounded in normal operation.  
PB  
I
3
Push button input. This pin must be at GNDD when not active or un-  
used. A rising edge sets the IE_PB flag. It also causes the part to  
wake up if it is in SLEEP or LCD mode. PB does not have an internal  
pull-up or pull-down resistor.  
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output.  
The circuit number denotes the equivalent circuit, as specified in Section 5.9.4.  
v1.1  
© 2007-2009 TERIDIAN Semiconductor Corporation  
119  
 复制成功!