80C32/80C52
MATRA MHS
Electrical Characteristics
* Notice
Absolute Maximum Ratings*
Stresses at or above those listed under “ Absolute Maximum Ratings”
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions may affect
device reliability.
Ambiant Temperature Under Bias :
C = commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I = industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65°C to + 150°C
Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V
Voltage on Any Pin to VSS . . . . . . . . . . . . . . . . . . . –0.5 V to V + 0.5 V
CC
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W
* This value is based on the maximum allowable die temperature and
the thermal resistance of the package
DC Parameters
TA = 0°C to 70°C ; VSS = 0 V ; VCC = 5 V ± 10 % ; F = 0 to 44 MHz
TA = –40°C + 85°C ; VSS = 0 V ; VCC = 5 V ± 10 % ; F = 0 to 36 MHz
SYMBOL
VIL
PARAMETER
MIN
– 0.5
MAX
0.2 Vcc – 0.1
Vcc + 0.5
Vcc + 0.5
UNIT
TEST CONDITIONS
Input Low Voltage
V
V
V
VIH
Input High Voltage (Except XTAL and RST)
Input High Voltage (for XTAL and RST)
Output Low Voltage (Port 1, 2 and 3)
0.2 Vcc + 1.4
0.7 Vcc
VIH1
VOL
0.3
0.45
1.0
V
V
V
IOL = 100 µA
IOL = 1.6 mA (note 2)
IOL = 3.5 mA
VOL1
VOH
Output Low Voltage (Port 0, ALE, PSEN)
Output High Voltage Port 1, 2, 3
0.3
0.45
1.0
V
V
V
IOL = 200 µA
IOL = 3.2 mA (note 2)
IOL = 7.0 mA
Vcc – 0.3
Vcc – 0.7
Vcc – 1.5
V
V
V
IOH = – 10 µA
IOH = – 30 µA
IOH = – 60 µA
VCC = 5 V ± 10 %
VOH1
Output High Voltage (Port 0, ALE, PSEN)
Vcc – 0.3
Vcc – 0.7
Vcc – 1.5
V
V
V
IOH = – 200 µA
IOH = – 3.2 mA
IOH = – 7.0 mA
VCC = 5 V ± 10 %
IIL
ILI
Logical 0 Input Current (Ports 1, 2 and 3)
Input leakage Current
– 50
± 10
– 650
50
µA
µA
Vin = 0.45 V
0.45 < Vin < Vcc
Vin = 2.0 V
ITL
Logical 1 to 0 Transition Current (Ports 1, 2 and 3)
Power Down Current
µA
IPD
RRST
CIO
ICC
µA
Vcc = 2.0 V to 5.5 V (note 1)
RST Pulldown Resistor
50
200
10
KOhm
pF
Capacitance of I/O Buffer
fc = 1 MHz, Ta = 25_C
Vcc = 5.5 V
Power Supply Current
Freq = 1 MHz Icc op
Icc idle
Freq = 6 MHz Icc op
Icc idle
1.8
1
10
4
mA
mA
mA
mA
Freq ≥ 12 MHz Icc op = 1.25 Freq (MHz) + 5 mA
Icc idle = 0.36 Freq (MHz) + 2.7 mA
10
Rev. E (31/08/95)