欢迎访问ic37.com |
会员登录 免费注册
发布采购

CC2430F32RTC 参数 Datasheet PDF下载

CC2430F32RTC图片预览
型号: CC2430F32RTC
PDF下载: 下载PDF文件 查看货源
内容描述: 真正的系统级芯片解决方案的2.4 GHz IEEE 802.15.4 / ZigBee的 [A True System-on-Chip solution for 2.4 GHz IEEE 802.15.4 / ZigBee]
分类和应用: 电信集成电路
文件页数/大小: 212 页 / 1862 K
品牌: TAOS [ TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS ]
 浏览型号CC2430F32RTC的Datasheet PDF文件第166页浏览型号CC2430F32RTC的Datasheet PDF文件第167页浏览型号CC2430F32RTC的Datasheet PDF文件第168页浏览型号CC2430F32RTC的Datasheet PDF文件第169页浏览型号CC2430F32RTC的Datasheet PDF文件第171页浏览型号CC2430F32RTC的Datasheet PDF文件第172页浏览型号CC2430F32RTC的Datasheet PDF文件第173页浏览型号CC2430F32RTC的Datasheet PDF文件第174页  
CC2430  
Radio : Output Power Programming  
14.27.1 VCO  
The VCO is completely integrated and  
operates at 4800 – 4966 MHz. The VCO  
frequencies in the desired band (2400-2483.5  
MHz).  
frequency is divided by  
2
to generate  
14.27.2 PLL self-calibration  
The VCO's characteristics will vary with  
temperature, changes in supply voltages, and  
the desired operating frequency.  
mode or TX mode is enabled, i.e. in the  
RX_CALIBRATE,  
TX_CALIBRATE  
and  
TX_ACK_CALIBRATE control states in Figure  
46 on page 167.  
In order to ensure reliable operation the VCO’s  
bias current and tuning range are  
automatically calibrated every time the RX  
14.28 Output Power Programming  
The RF output power of the device is  
programmable and is controlled by the  
TXCTRLL RF register. Table 45 shows the  
output power for different settings, including  
the complete programming of the TXCTRLL  
register and the current consumption in the  
whole device.  
For optimum link quality it is recommended to  
set TXCTRLLto 0x5F.  
Table 45: Output power settings  
Output Power  
[dBm]  
Device current  
consumption [mA]  
TXCTRLLregister  
value  
0xFF  
0xDF  
0xBF  
0x9F  
0x7F  
0x5F  
0x3F  
0x1F  
0x1B  
0x17  
0x13  
0x0F  
0x0B  
0x07  
0x06  
0x03  
0.6  
32.4  
31.3  
30.3  
29.2  
28.1  
26.9  
25.7  
24.5  
23.6  
22.8  
21.9  
21.0  
20.1  
19.2  
18.8  
18.3  
0.5  
0.3  
0.2  
-0.1  
-0.4  
-0.9  
-1.5  
-2.7  
-4.0  
-5.7  
-7.9  
-10.8  
-15.4  
-18.6  
-25.2  
14.29 Input / Output Matching  
The RF output and DC bias can be done using  
different topologies. Some are shown in Figure  
6 on page 28.  
The RF input / output is differential (RF_Nand  
RF_P). In addition there is supply switch output  
pin (TXRX_SWITCH) that must have an  
external DC path to RF_Nand RF_P.  
Component values are given in Table 23 on  
page 29. If  
implemented, no balun is required.  
a
differential antenna is  
In RX mode the TXRX_SWITCH pin is at  
ground and will bias the LNA. In TX mode the  
TXRX_SWITCHpin is at supply rail voltage and  
will properly bias the internal PA.  
If a single ended output is required (for a  
single ended connector or a single ended  
antenna), a balun should be used for optimum  
performance.  
CC2430 Data Sheet (rev. 2.1) SWRS036F  
Page 170 of 211