欢迎访问ic37.com |
会员登录 免费注册
发布采购

CC1110FX 参数 Datasheet PDF下载

CC1110FX图片预览
型号: CC1110FX
PDF下载: 下载PDF文件 查看货源
内容描述: 低功耗低于1 GHz的射频系统级芯片(SoC )与MCU,存储器,收发器和USB控制器 [Low-power sub-1 GHz RF System-on-Chip (SoC) with MCU, memory, transceiver, and USB controller]
分类和应用: 存储射频控制器
文件页数/大小: 240 页 / 2823 K
品牌: TAOS [ TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS ]
 浏览型号CC1110FX的Datasheet PDF文件第73页浏览型号CC1110FX的Datasheet PDF文件第74页浏览型号CC1110FX的Datasheet PDF文件第75页浏览型号CC1110FX的Datasheet PDF文件第76页浏览型号CC1110FX的Datasheet PDF文件第78页浏览型号CC1110FX的Datasheet PDF文件第79页浏览型号CC1110FX的Datasheet PDF文件第80页浏览型号CC1110FX的Datasheet PDF文件第81页  
CC1110Fx / CC1111Fx  
13 Peripherals  
In  
the  
following  
sub-sections,  
each  
CC1110Fx/CC1111Fx peripheral is described in  
detail.  
13.1 Power Management and Clocks  
This section describes the Power Management  
Controller. The Power Management Controller  
controls the use of active mode, power modes,  
and clock control.  
using clock gating and turning off oscillators to  
reduce dynamic power consumption.  
The CC1110Fx/CC1111Fx has one active mode  
and four power modes, called PM0, PM1, PM2  
and PM3, where PM3 has the lowest power  
consumption. Please note the minimum  
requirement on high speed crystal oscillator  
powerdown time in all modes of operation for  
13.1.1 Power Management Introduction  
The CC1110Fx/CC1111Fx uses different operating  
modes to allow low-power operation. Ultra-low-  
power operation is obtained by turning off  
power supply to modules to avoid static  
(leakage) power consumption and also by  
CC1110Fx, see Table 11.  
The different  
operating modes are shown in Table 48.  
Operating Mode  
High-speed Oscillator  
Low-speed Oscillator  
Digital Voltage  
Regulator  
CPU  
None  
None  
Configuration  
A
B
C
A
B
C
High speed XOSC  
HS RCOSC  
Low power RCOSC  
32.768 kHz XOSC  
Active  
PM0  
PM1  
PM2  
PM3  
B and / or C  
B or C  
B or C  
B or C  
B or C  
A
On  
On  
On  
Off  
Off  
Running  
Idle  
B and / or C  
A
A
A
Idle  
Idle  
Idle  
Table 48: Operating Modes  
Active mode: The full functional mode. The  
voltage regulator to the digital core is on and  
either the high speed RC oscillator or the high  
speed crystal oscillator or both are running.  
Either the Low power RC oscillator or the  
32.768 kHz crystal oscillator is running.  
expires. The CC1111Fx will lose all USB state  
information when PM2 is entered. Thus, PM2  
should not be used with USB.  
PM3: The voltage regulator to the digital core  
is turned off. None of the oscillators are  
running. The system will go to active mode on  
reset or an external interrupt. The CC1111Fx will  
lose all USB state information when PM3 is  
entered. Thus, PM3 should not be used with  
USB.  
PM0: Same as avtive mode, but the CPU is  
idle, meaning that no code is being executed.  
PM1: The voltage regulator to the digital part is  
on. Neither the high speed crystal oscillator nor  
the high speed RC oscillator is running. Either  
the low power RC oscillator or the 32.768 kHz  
crystal oscillator is running. The system will go  
to active mode on reset or an external interrupt  
or when the Sleep Timer expires.  
When an external interrupt occurs in PM1,  
PM2, or PM3, or a Sleep Timer interrupt occur  
in PM1 and PM2, active mode will be entered  
and the code will start executing from where it  
entered PM1/2/(3). Any enabled interrupt will  
take the device from PM0 to active mode, and  
also in this case the code will start executing  
from where it entered PM0. A reset, however,  
will take the chip from any of the four power  
modes to active mode, but the code will start  
executing from the start of the program.  
PM2: The voltage regulator to the digital core  
is turned off. Neither the high speed crystal  
oscillator nor the high speed RC oscillator is  
running. Either the low power RC oscillator or  
the 32.768 kHz crystal oscillator is running.  
The system will go to active mode on reset or  
an external interrupt or when the Sleep Timer  
SWRS033E  
Page 77 of 239