SyncMOS Technologies Inc.
VIL1
VIL2
VIL3
VIH1
VIH2
VIH3
IIN1
ITL
ILI
VOL1
VOL2
VOH1
VOH2
ISK1
ISK2
ISR1
ISR2
RRST
CIO
Input LOW voltage, P0, P1, P2, P3, P4, /EA
Input LOW voltage, RST
Input LOW voltage, XTAL1
Input HIGH voltage, P0, P1, P2, P3, P4, /EA
Input HIGH voltage, RST
Input HIGH voltage, XTAL1
Input current LOW level Port 1,2,3,4
Transition current High to Low Port 1,2,3,4
Input leakage current P0, /EA
Output LOW voltage, Port 0,ALE, /PSEN
Output Low voltage Port 1,2,3,4
Output High voltage Port0, ALE, /PSEN
Output High voltage Port 1,2,3,4
Sink Current Port 1, 2, 3, 4
Sink Current Port 0,ALE, /PSEN
Source Current Port 1, 2, 3, 4
Source Current Port 0,ALE, /PSEN
Internal RESET pull-down resistor
Pin capacitance
VCC = 3.6V
VCC = 3.6V
VCC = 3.6V
VCC = 3.6V
VCC = 3.6V
VCC = 3.6V
VCC = 3.0V ~3.6V,
VIN = 0.45V.
See note 4
VCC = 3.6V, VIN = 2.0 V
VCC = 3.0V ~3.6V,
0.45V<VIN<VCC
OUTPUT
IOL = 6mA，VCC =3.3V
IOL = 5mA，VCC =3.3V
IOH =-300uA，VCC =3.3V
IOH =-20µA，VCC =3.3V
VCC = 3.3V, VIN = 0.4 V
VCC = 3.3V, VIN = 0.4 V
VCC = 3.3V, VIN = 2.4 V
VCC = 3.3V, VIN = 2.4 V
Test freq=1MHz, TA=25℃
0
0
0
0.6 VCC
-0.4
0.6 VCC
-0.4
0.8 VCC
-10
-75
-10
SM89S16R1
0.2 VCC -0.2
0.2 VCC -0.2
0.2 VCC -0.2
VCC + 0.2
VCC + 0.2
VCC + 0.2
50
400
10
0.4
0.4
2.4
2.4
6
8
-80
-8
300
10
V
V
V
V
V
V
µA
µA
µA
V
V
V
V
mA
mA
uA
mA
kΩ
pF
8-Bits Micro-controller
With 64KB Flash ROM & IKB RAM & RTC & ADC & PWM & PDWU embedded
50
NOTES FOR DC ELECTRICAL CHARACTERISTICS
1.
The operating supply current is measured with all output disconnected;
XTAL1 driven with tr = tf = 5ns; VIL = VSS+0.5V; VIH=VCC-0.5V; XTAL2 not connect;
/EA=RST=Port0=VDD;
2.
The IDLE MODE supply current is measured with all output pins disconnected;
XTAL1 driven with tr = tf = 5ns; VIL = VSS+0.5V; VIH=VCC-0.5V; XTAL2 not connect;
/EA=Port0=VDD;
3.
The POWER-DOWN MODE supply current is measured with all output pins disconnected;
VIL = VSS+0.5V; VIH=VCC-0.5V; XTAL2 not connect; /EA= Port0=VDD;
4.
Port 1, 2, 3, and 4 sources a transition current when they are being externally driven from HIGH to LOW. The transition current reaches its
maximum value when VIN is approximately 2V.
5.
Capacities loading on port 0 and 2 may cause spurious noise to be superimposed on VOL of ALE and port 1, 3, and 4. The noise is due to external
bus capacitance discharging into port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the worst cases
(capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify ALE with a Schmitt
Trigger, or use an address latch with a Schmitt trigger STROBE input.
Specifications subject to change without notice contact your sales representatives for the most recent information.
9
SM89S16R1 V1.0 JANUARY 2005
SYNCMOS [ SYNCMOS TECHNOLOGIES,INC ]
