SMS64
Preliminary
RECOMMENDED OPERATING CONDITIONS
ABSOLUTE MAXIMUM RATINGS
Temperature Range(Ambient)...……-40° C to +85°C
Temperature Under Bias ...................... -55°C to 125°C
Supply Voltage………………….………2.7V to 6.0V 1/
Storage Temperature............................ -65°C to 150°C
Package Thermal Resistance (θ JA)
Terminal Voltage with Respect to GND:
48 Lead SSOP…………………………………80oC/W
Moisture Classification Level 1 (MSL 1) per J-STD- 020
VCCA, VCCB, VCCC, VCCD, VCCE, VCCF..-0.3V to 6.0V
VMA, VMB, VMC, VMD, VME, VMF...............-0.3V to 6.0V
PUPA, PUPB, PUPC, PUPD, PUPE, PUPF .............. 15.5V
All Others ......................................................VCC + 0.7V
Output Short Circuit Current ............................... 100mA
RELIABILITY CHARACTERISTICS
Data Retention…………………………..…..100 Years
Endurance…………………….……….100,000 Cycles
Lead Solder Temperature (10 secs).................... 300°C
ESD Rating per JEDEC…………………………..2000V
Latch-Up testing per JEDEC……………......+/- 100mA
Stresses listed under Absolute Maximum Ratings may cause permanent
damage to the device. These are stress ratings only and functional operation
of the device at these or any other conditions outside those listed in the
operational sections of the specification is not implied. Exposure to any
absolute maximum rating for extended periods may affect device performance
and reliability.
recommended.
Devices are ESD sensitive. Handling precautions are
DC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Notes
Min.
Typ.
Max
Unit
Device supply voltage
defined by the highest of
the six VCC inputs. Must
be > 2.7V. – Note 1/
Supply Voltage VCCA, VCCB, VCCC,
VCCD, VCCE, VCCF
VCC
2.7
6.0
V
Active Current with PUP
Outputs configured as
high-side drivers enabled
Quiescent Current high-
side PUP Outputs disabled
IDD (ON)
2
mA
Power Supply Current
IDD (Off)
PVIT
1
mA
V
Programmable Threshold (VCC and VM
Inputs)
8-bit resolution 20mV/bit
0.9
0
6.0
“naked” mode, V input
VTH
Fixed threshold Voltage
0.5
V
disconnected from ground
PUP characteristics when configured as high-side driver
Option 1 (MOSFETs on)
Option 2 (MOSFETs on)
IPUPSINK = 2mA
14.5
10.5
V
V
V
PVPUP
Programmable PUP Output
VPUP OFF PUP Output
0.4
8
When configured as high-
side driver and with
MOSFET switches on
When Configured as High
Side Driver
IPUP
PUP Drive Current
PUP Slew Rate
µA
SRPUP
250
V/s
PUP characteristics when configured as a logic output
VOL Output Low Voltage ISINK = 2mA
All other input and output characteristics
0
0.4
V
0.9xVI
0.7xVI
-0.1
Input High Voltage (FS#, PWR_ON/OFF, VCC = 2.7V
MR#)
VI
V
V
V
V
VIH
VCC = 5.0V
VI
0.1xVI
0.3xVI
Input Low Voltage (FS#, PWR_ON/OFF, VCC = 2.7V
VIL
MR#)
VCC = 5.0V
ISINK = 2mA
-0.1
Open Drain Outputs (RST_A#, RST_B#,
IRQ#, HEALTHY#)
VOL
0
0.4
V
Notes: 1/ At least one of the VCC inputs needs to be at or above 2.7V for proper device operation.
Summit Microelectronics, Inc
2060 2.22 10/09/03
7
SUMMIT [ SUMMIT MICROELECTRONICS, INC. ]
