LM139,A-LM239,A-LM339,A
ELECTRICAL CHARACTERISTICS
V
CC
+
= +5V, V
CC
-
= GND, T
amb
= +25°C (unless otherwise specified)
Symbol
Parameter
LM139A - LM239A
LM339A
Min.
V
io
Input Offset Voltage - note
1)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Offset Current
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Bias Current (I
+
or I
-
) - note
2)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Large Signal Voltage Gain
V
CC
= 15V, R
L
= 15kΩ, V
o
= 1V to 11V
Supply Current (all comparators)
V
CC
= +5V, no load
V
CC
= +30V, no load
Input Common Mode Voltage Range - note
3)
V
CC
= 30V
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Differential Input Voltage -note
4)
Low Level Output Voltage
V
id
= -1V, I
sink
= 4mA
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
High Level Output Current (V
id
= 1V)
I
OH
V
CC
= V
o
= 30V
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Output Sink Currrent
V
id
= 1V, V
o
= 1.5V
Response Time - note
5)
R
L
= 5.1kΩ connected to V
CC+
Large Signal Response Time
R
L
= 5.1kΩ connected to V
CC+
, e
l
= TTL,
V
(ref)
= +1.4v
6
0.1
1
16
1.3
6
16
1.3
0.1
1
nA
µA
mA
µs
50
Typ.
1
Max.
2
4
25
100
100
300
50
2
2.5
LM139- LM239
LM339
Min
Typ.
1
Max.
5
9
50
150
250
400
mV
Unit
I
io
3
5
nA
I
ib
25
25
nA
A
vd
200
1.1
1.3
200
1.1
1.3
2
2.5
V/mV
mA
I
CC
V
icm
0
0
V
CC+
-1.5
V
CC+
-2
V
CC+
0
0
V
CC+
-1.5
V
CC+
-2
V
CC+
V
V
id
V
V
OL
250
400
700
250
400
700
mV
Isink
tre
trel
1.
2.
3.
4.
5.
300
300
ns
At output switch point, V
o
≈
1.4V, R
s
= 0 with V
CC +
from 5V to 30V, and over the full common-mode range (0V to V
CC +
-1.5V).
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the
output, so no loading charge exists on the reference of input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the
common-mode voltage range is V
CC +
-1.5V, but either or both inputs can go to +30V without damage
The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be obtained
Posistive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than -0.3V (or 0.3V bellow the negative power supply, if
used).
3/10
STMICROELECTRONICS [ STMICROELECTRONICS ]
