LM193, LM193A, LM293, LM293A, LM393, LM393A
Electrical Characteristics
4
Table 3.
Symbol
Electrical Characteristics
V
CC+
= +5V, V
CC-
= 0V, T
amb
= +25°C (unless otherwise specified)
Parameter
Input Offset Voltage - note
(1)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Offset Current
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Bias Current (I
+
or I
-
) - note
(2)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Large Signal Voltage Gain
V
CC
= 15V, R
L
= 15kΩ, V
o
= 1V to 11V
Supply Current (all comparators)
V
CC
= +5V, no load
V
CC
= +30V, no load
Input Common Mode Voltage Range - note
(3)
V
CC
= 30V
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Differential Input Voltage -note
(4)
Low Level Output Voltage
V
id
= -1V, I
sink
= 4mA
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
High Level Output Current (V
id
= 1V)
V
CC
= V
o
= 30V
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Output Sink Current
V
id
= 1V, V
o
= 1.5V
Response Time - note
(5)
R
L
= 5.1kΩ connected to V
CC+
Large Signal Response Time
R
L
= 5.1kΩ connected to V
CC+
, e
l
= TTL,
V
(ref)
= +1.4v
6
50
LM193A - LM293A
LM393A
Min.
V
io
Typ.
1
Max.
2
4
25
100
100
300
50
1
2.5
LM193- LM293
LM393
Min
Typ.
1
Max.
5
9
50
150
250
400
mV
Unit
I
io
3
5
nA
I
ib
A
vd
I
CC
25
25
nA
200
0.4
1
200
0.4
1
1
2.5
V/mV
mA
V
icm
V
id
V
OL
0
0
V
CC+
-1.5
V
CC+
-2
V
CC+
0
0
V
CC+
-1.5
V
CC+
-2
V
CC+
V
250
400
700
250
400
700
mV
I
OH
0.1
1
16
1.3
6
0.1
1
16
1.3
nA
µA
mA
µs
ns
I
SINK
tre
trel
300
300
1. At output switch point, V
o
≈
1.4V, R
s
= 0 with V
CC+
from 5V to 30V, and over the full common-mode range (0V to V
CC +
-
1.5V).
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant,
independent of the state of the output, so no loading charge exists on the reference of input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The
upper end of the common-mode voltage range is V
CC+
-1.5V, but either or both inputs can go to +30V without damage.
4. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be
obtained.
5. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -
0.3V (or 0.3V bellow the negative power supply, if used).
5/15