LM2903
ELECTRICAL CHARACTERISTICS
V
CC+
= 5V, V
cc-
= GND, T
amb
= 25°C (unless otherwise specified)
Symbol
V
IO
Input Offset Voltage
1)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
.
Input Offset Current
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max.
Input Bias Current
2)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max.
Large Signal Voltage Gain (V
cc
= 15V,R
L
=15kΩ, V
o
=1 to 11V)
Supply Current (all comparators)
V
CC
= 5V, no load
V
CC
= 30V, no load
Input Common Mode Voltage Range (V
cc
= 30V)
3)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max.
Differential Input Voltage
4)
Low Level Output Voltage (V
id
= -1V, I
sink
= 4mA)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
High Level Output Current (V
CC
=V
o
=30V, V
id
= 1V)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Output Sink Current (V
id
= -1V,V
o
= 1.5V)
Small Signal Response Time
5)
(R
L
= 5.1kΩ to V
CC
+
)
Large Signal Response Time
6)
TTL Input (V
ref
= +1.4 V, R
L
=5.1kΩ to V
CC+
)
Output Signal at 50% of final value
Output Signal at 95 % of final value
6
0
0
25
Parameter
Min.
Typ.
1
Max.
7
15
50
150
250
400
Unit
mV
I
IO
5
nA
I
IB
A
VD
I
CC
25
200
0.4
1
nA
V/mV
1
2.5
V
CC+
-1.5
V
CC+
-2
V
CC+
mA
V
ICM
V
ID
V
OL
V
V
mV
250
400
700
I
OH
I
SINK
t
RE
0.1
1
16
1.3
nA
µA
mΑ
µs
t
REL
500
1
ns
µs
1.
2.
3.
4.
At output switch point, V
O
≈
1.4V, R
S
= 0Ω with V
CC
+
from 5V to 30V, and over the full input common-mode range (0V to V
CC
+
–1.5V).
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the
output, so no loading charge exists on the reference of input lines
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the
common-mode voltage range is V
CC
+
–1.5V, but either or both inputs can go to +30V without damage.
Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state.
The low input voltage state must not be less than –0.3V (or 0.3V below the negative power supply, if used)
The response time specified is for a 100mV input step with 5mV overdrive.
Maximum values are guaranteed by design & evaluation.
5.
6.
3/9