8 Mbit SPI Serial Flash
SST25VF080B
Data Sheet
Instructions
Instructions are used to read, write (Erase and Program),
and configure the SST25VF080B. The instruction bus
cycles are 8 bits each for commands (Op Code), data, and
addresses. Prior to executing any Byte-Program, Auto
Address Increment (AAI) programming, Sector-Erase,
Block-Erase, Write-Status-Register, or Chip-Erase instruc-
tions, the Write-Enable (WREN) instruction must be exe-
cuted first. The complete list of instructions is provided in
Table 5. All instructions are synchronized off a high to low
transition of CE#. Inputs will be accepted on the rising edge
of SCK starting with the most significant bit. CE# must be
driven low before an instruction is entered and must be
driven high after the last bit of the instruction has been
shifted in (except for Read, Read-ID, and Read-Status-
Register instructions). Any low to high transition on CE#,
before receiving the last bit of an instruction bus cycle, will
terminate the instruction in progress and return the device
to standby mode. Instruction commands (Op Code),
addresses, and data are all input from the most significant
bit (MSB) first.
TABLE 5: Device Operation Instructions
Address
Cycle(s)2
Dummy
Cycle(s)
Data
Cycle(s)
Instruction
Description
Op Code Cycle1
0000 0011b (03H)
0000 1011b (0BH)
0010 0000b (20H)
Read
Read Memory
3
3
3
0
1
0
1 to ∞
1 to ∞
0
High-Speed Read
4 KByte Sector-Erase3
Read Memory at higher speed
Erase 4 KByte of
memory array
32 KByte Block-Erase4
64 KByte Block-Erase5
Chip-Erase
Erase 32 KByte block
of memory array
0101 0010b (52H)
1101 1000b (D8H)
3
3
0
0
0
0
0
0
0
Erase 64 KByte block
of memory array
Erase Full Memory Array
0110 0000b (60H) or
1100 0111b (C7H)
Byte-Program
AAI-Word-Program6
To Program One Data Byte
0000 0010b (02H)
1010 1101b (ADH)
3
3
0
0
1
Auto Address Increment
Programming
2 to ∞
RDSR7
EWSR
WRSR
WREN
WRDI
Read-Status-Register
Enable-Write-Status-Register
Write-Status-Register
Write-Enable
0000 0101b (05H)
0101b 0000b (50H)
0000 0001b (01H)
0000 0110b (06H)
0000 0100b (04H)
0
0
0
0
0
3
0
0
0
0
0
0
1 to ∞
0
1
0
Write-Disable
0
RDID8
Read-ID
1001 0000b (90H) or
1010 1011b (ABH)
1 to ∞
JEDEC-ID
EBSY
JEDEC ID read
1001 1111b (9FH)
0111 0000b (70H)
0
0
0
0
3 to ∞
Enable SO to output RY/BY#
status during AAI programming
0
DBSY
Disable SO to output RY/BY#
status during AAI programming
1000 0000b (80H)
0
0
0
T5.0 1296
1. One bus cycle is eight clock periods.
2. Address bits above the most significant bit of each density can be VIL or VIH.
3. 4KByte Sector Erase addresses: use AMS-A12, remaining addresses are don’t care but must be set either at VIL or VIH.
4. 32KByte Block Erase addresses: use AMS-A15, remaining addresses are don’t care but must be set either at VIL or VIH.
5. 64KByte Block Erase addresses: use AMS-A16, remaining addresses are don’t care but must be set either at VIL or VIH.
6. To continue programming to the next sequential address location, enter the 8-bit command, ADH, followed by 2 bytes of data to be
programmed. Data Byte 0 will be programmed into the initial address [A23-A1] with A0=0, Data Byte 1 will be programmed into the
initial address [A23-A1] with A0=1.
7. The Read-Status-Register is continuous with ongoing clock cycles until terminated by a low to high transition on CE#.
8. Manufacturer’s ID is read with A0=0, and Device ID is read with A0=1. All other address bits are 00H. The Manufacturer’s ID and
device ID output stream is continuous until terminated by a low-to-high transition on CE#.
©2010 Silicon Storage Technology, Inc.
S71296-04-000
01/10
8
SST [ SILICON STORAGE TECHNOLOGY, INC ]
