CXA1814N
(DC characteristics 2)
(Unless otherwise specified, Ta = 25 °C, VCC = 3.15 V)
Rating values
Item
Symbol
Conditions
Unit Remarks
Min.
0
Typ.
Max.
CLOG REF input voltage
SP/LP REF input voltage
CLOG detection high check
CLOG detection low check
CLOG output voltage
VCC1
VSC2
V
CC
0
V
CC
V
SPIN = 50 mVp-p, 5 MHz/GCA2 = 1000/CLOGREF = 0.39 V
SPIN = 150 mVp-p, 5 MHz/GCA2 = 1000/CLOGREF = 0.39 V
SPIN = 500 mVp-p, 5 MHz/GCA2 = 1000/CLOGREF = COMPREF
VCC = 3.0...4.0 V
2.4
0.4
0.4
Vclgl
Vclgh
Vspl
0.01
3.0
SPIN = AC GND/GCA2=1000/CLOGREF = COMPREF
VCC = 3.0...4.0 V
2.5
2.5
PB SP/LP output voltage
SPIN = AC GND/MODRATIO: See fig1
3.0
V
Note 1
SPLPREF = Vref/VCC=3...4 V/GCA2 = 1000
SPIN = 500 mVp-p, 5 MHz/MODRATIO: See fig1
SPLPREF = Vref/VCC=3...4 V/GCA2 = 1000
Pins 14, 15 and 17; VCC = 3 to 4 V
Vsph
0.01
0.4
“High” level input voltage
“Low” level input voltage
“High” level input current
“Low” level input current
CLOG identification time
Vih
Vil
2.1
VCC
Pins 14, 15 and 17; VCC = 3 to 4 V
–0.4
0.8
1
Iih
Pins 14, 15 and 17; VCC = 3 to 4 V
0
–0.5
1.3
7.5
50
µA
Note 1
Iil
Pins 14, 15 and 17; VCC = 3 to 4 V
–1
0.7
4
Tcl1
Tcl2
Tsp1
Tsp2
VEnv0
Dvenv
Venv1
SPIN = 500 mVp-p, 5 MHz/Burst = 0.5 Hz/GCA2 = 1000
CLOGREF = COMPREF (See: fig2)
2.6
10.6
70
mS
SPLP identification time
SPIN = 500 mVp-p, 5 MHz/Burst = 0.5 Hz/GCA2 = 1000
SPLPREF = Vref/MODRATIO = See: fig1 (See: fig3)
SPIN = AC GND, GCA2 = 0000; ENVOUT pin voltage
SPIN = AC GND, GCA2 = 0000; ENVOUT – COMPREF voltage
ENVOUT voltage difference when SPIN = 0 V and 0.5 Vp-p, 5
MHz, GCA2 = 1111 and VCC = 3.15 V
30
30
50
70
ENV OUT DC voltage
0.425
–80
2.3
0.525
0
0.625
80
V
RF detection offset voltage
RF detection output voltage
mV
2.5
V
Venv2
ENVOUT voltage difference when SPIN = 0 V and 0.5 Vp-p, 5
MHz, GCA2 = 1111 and VCC = 3.0 V
2.2
2.4
CLOG REF input current
MOD RATIO input current
SP/LP REF input current
ICC1h
ICC1l
Pin current value when CLOG REF = 3.15 V
Pin current value when CLOG REF = 0 V
Pin current value when MOD RATIO = 3.15 V
Pin current value when MOD RATIO = 0 V
Pin current value when SPLPREF = 3.15 V
Pin current value when SPLPREF = 0 V
0
–0.1
0
1
1
–1
–1
–1
ICC1h
µA
–0.1
0
ICC1h
1
–0.1
Switching time between
Time until RECATF stabilizes when RPPBMODE goes from high to
low
20
25
µS
playback and recording mode
Switching time between
standby and playback mode
Time until PBATF Error stabilizes when STBY goes from high to
low
mS
Note 1) The Typ. value is VCC = 3.15 V
– 10 –
SONY [ SONY CORPORATION ]
