欢迎访问ic37.com |
会员登录 免费注册
发布采购

SN8F2288 参数 Datasheet PDF下载

SN8F2288图片预览
型号: SN8F2288
PDF下载: 下载PDF文件 查看货源
内容描述: 8位微控制器 [8-Bit Micro-Controller]
分类和应用: 微控制器
文件页数/大小: 163 页 / 3660 K
品牌: SONIX [ SONIX TECHNOLOGY COMPANY ]
 浏览型号SN8F2288的Datasheet PDF文件第121页浏览型号SN8F2288的Datasheet PDF文件第122页浏览型号SN8F2288的Datasheet PDF文件第123页浏览型号SN8F2288的Datasheet PDF文件第124页浏览型号SN8F2288的Datasheet PDF文件第126页浏览型号SN8F2288的Datasheet PDF文件第127页浏览型号SN8F2288的Datasheet PDF文件第128页浏览型号SN8F2288的Datasheet PDF文件第129页  
SN8F2280 Series  
USB 2.0 Full-Speed 8-Bit Micro-Controller  
11.2 SIOM MODE REGISTER  
0B0H  
Bit 7  
SENB  
R/W  
0
Bit 6  
START  
R/W  
0
Bit 5  
SRATE1  
R/W  
Bit 4  
SRATE0  
R/W  
Bit 3  
MLSB  
R/W  
0
Bit 2  
SCKMD  
R/W  
Bit 1  
CPOL  
R/W  
0
Bit 0  
CPHA  
R/W  
0
SIOM  
Read/Write  
After reset  
0
0
0
Bit 7  
SENB: SIO function control bit.  
0 = Disable (P2.0~P2.2 is general purpose I/O port).  
1 = Enable (P2.0~P2.2 is SIO pins).  
Bit 6  
START: SIO progress control bit.  
0 = End of transfer.  
1 = Progressing.  
Bit [5:4] SRATE1:0: SIO’s transfer rate select bit. These 2-bits are workless when SCKMD=1.  
00 = Fcpu/2.  
01 = Fcpu/64  
10 = Fcpu/32  
11 = Fcpu/16.  
Bit 3  
Bit 2  
Bit 1  
Bit 0  
MLSB: MSB/LSB transfer first.  
0 = MSB transmit first.  
1 = LSB transmit first.  
SCKMD: SIO’s clock mode select bit.  
0 = Internal. (Master mode)  
1 = External. (Slave mode)  
CPOL: SIO’s transfer clock edge select bit.  
0 = SCK idle status is low status  
1 = SCK idle status is high status  
CPHA: The Clock Phase bit controls the phase of the clock on which data is sampled.  
0 = Data receive at the fisrt clock phase.  
1 = Data receive at the second clock phase.  
’
Note: 1. If SCKMD=1 for external clock, the SIO is in SLAVE mode. If SCKMD=0 for internal clock,  
the SIO is in MASTER mode.  
2. Don’t set SENB and START bits in the same time. That makes the SIO function error.  
Because SIO function is shared with Port2 for P2.0 as SCK, P2.1 as SDO and P2.2 as SDI.  
The following table shown the Port2[2:0] I/O mode behavior and setting when SIO function enable and disable.  
SENB=1 (SIO Function Enable)  
(SCKMD=1)  
P2.0 will change to Input mode automatically, no matter what P2M  
SIO source = External clock  
(SCKMD=0)  
setting  
P2.0/SCK  
P2.0 will change to Output mode automatically, no matter what  
SIO source = Internal clock  
SIO = Transmitter/Receiver  
P2M setting  
P2.1/SDO  
P2.2/SDI  
P2.1 will change to Output mode automatically, no matter what  
P2M setting  
P2.2 must be set as Input mode in P2M ,or the SIO function will be abnormal  
SENB=0 (SIO Function Disable)  
P2.0/P2.1/P2.2 Port2[2:0] I/O mode are fully controlled by P2M when SIO function is disable  
SONiX TECHNOLOGY CO., LTD  
Page 125  
Version 1.1