欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN9218 参数 Datasheet PDF下载

LAN9218图片预览
型号: LAN9218
PDF下载: 下载PDF文件 查看货源
内容描述: 高性能单芯片10/100以太网控制器,带有HP Auto-MDIX的 [High-Performance Single- Chip 10/100 Ethernet Controller with HP Auto-MDIX]
分类和应用: 控制器以太网局域网(LAN)标准
文件页数/大小: 130 页 / 1558 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN9218的Datasheet PDF文件第23页浏览型号LAN9218的Datasheet PDF文件第24页浏览型号LAN9218的Datasheet PDF文件第25页浏览型号LAN9218的Datasheet PDF文件第26页浏览型号LAN9218的Datasheet PDF文件第28页浏览型号LAN9218的Datasheet PDF文件第29页浏览型号LAN9218的Datasheet PDF文件第30页浏览型号LAN9218的Datasheet PDF文件第31页  
High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX  
Datasheet  
3.5.1  
Magic Packet Detection  
Setting the Magic Packet Enable bit (MPEN) in the “WUCSR—Wake-up Control and Status Register”,  
places the LAN9218 MAC in the “Magic Packet” detection mode. In this mode, normal data reception  
is disabled, and detection logic within the MAC examines receive data for a Magic Packet. The  
LAN9218 can be programmed to notify the host of the “Magic Packet” detection with the assertion of  
the host interrupt (IRQ) or assertion of the power management event signal (PME). Upon detection,  
the Magic Packet Received bit (MPR) in the WUCSR is set. When the host clears the MPEN bit the  
LAN9218 will resume normal receive operation. Please refer to Section 5.4.12, "WUCSR—Wake-up  
Control and Status Register," on page 102 for additional information on this register  
In Magic Packet mode, the Power Management Logic constantly monitors each frame addressed to  
the node for a specific Magic Packet pattern. It checks only packets with the MAC’s address or a  
broadcast address to meet the Magic Packet requirement. The Power Management Logic checks each  
received frame for the pattern 48h FF_FF_FF_FF_FF_FF after the destination and source address  
field.  
Then the Function looks in the frame for 16 repetitions of the MAC address without any breaks or  
interruptions. In case of a break in the 16 address repetitions, the PMT Function scans for the  
48'hFF_FF_FF_FF_FF_FF pattern again in the incoming frame.  
The 16 repetitions may be anywhere in the frame but must be preceded by the synchronization stream.  
The device will also accept a multicast frame, as long as it detects the 16 duplications of the MAC  
address. If the MAC address of a node is 00h 11h 22h 33h 44h 55h, then the MAC scans for the  
following data sequence in an Ethernet: Frame.  
Destination Address Source Address ……………FF FF FF FF FF FF  
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55  
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55  
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55  
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55  
…CRC  
It should be noted that Magic Packet detection can be performed when LAN9218 is in the D0 or D1  
power states. In the D0 state, “Magic Packet” detection is enabled when the MPEN bit is set. In the  
D1 state, Magic Packet detection, as well as wake-up frame detection, are automatically enabled when  
the device enters the D1 state.  
3.6  
Host Bus Operations  
3.6.1  
32-bit vs. 16-bit Host Bus Width Operation  
The LAN9218 can be configured to communicate with the host bus via either a 32-bit or a 16-bit bus.  
An external strap is used to select between the two modes. 32-bit mode is the native environment for  
the LAN9218. Ethernet controller and no special requirements exist for communication in this mode.  
However, when this part is used in the 16-bit mode, two writes or reads must be performed back to  
back to properly communicate.  
The bus width is set by strapping the EEDIO pin; this setting can be read from bit 2 of the “Hardware  
Configuration Register”. Please refer to Section 5.3.9, "HW_CFG—Hardware Configuration Register,"  
on page 76 for additional information on this register.  
SMSC LAN9218  
Revision 1.5 (07-18-06)  
DATA2S7HEET