欢迎访问ic37.com |
会员登录 免费注册
发布采购

EVB-EMC1053C 参数 Datasheet PDF下载

EVB-EMC1053C图片预览
型号: EVB-EMC1053C
PDF下载: 下载PDF文件 查看货源
内容描述: 1C三重温度传感器与两个区域阻力纠错和霍特 [1C Triple Temperature Sensor with Resistance Error Correction and Hotter of Two Zones]
分类和应用: 传感器温度传感器
文件页数/大小: 26 页 / 550 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号EVB-EMC1053C的Datasheet PDF文件第7页浏览型号EVB-EMC1053C的Datasheet PDF文件第8页浏览型号EVB-EMC1053C的Datasheet PDF文件第9页浏览型号EVB-EMC1053C的Datasheet PDF文件第10页浏览型号EVB-EMC1053C的Datasheet PDF文件第12页浏览型号EVB-EMC1053C的Datasheet PDF文件第13页浏览型号EVB-EMC1053C的Datasheet PDF文件第14页浏览型号EVB-EMC1053C的Datasheet PDF文件第15页  
1°C Triple Temperature Sensor with Resistance Error Correction & Hotter of Two Zones  
Datasheet  
Chapter 3 Product Description  
The EMC1053 is an SMBus sensor that monitors three temperature zones for use in a personal  
computer or embedded environment. The part may be used as a companion to one of SMSC’s broad  
line of SIO host devices to perform fan control and thermal management.  
A typical system drawing of the EMC1053 is shown in Figure 3.1.  
EMC1053  
DP1  
Host  
DN1  
DP2  
SMBus  
Interface  
SMBus  
DN2  
Internal  
Diode  
Figure 3.1 EMC1053 Diode System  
3.1  
Power Modes  
The EMC1053 has two power modes.  
„
Run Mode - In this mode, the temperature monitors are active and converting at the programmed  
conversion rate. The average power dissipation will depend on the conversion rate. When the  
EMC1053 is not actively converting a channel, it goes into a lower power wait state.  
„
Standby Mode (power-up default) - in this mode, the EMC1053 is put into a low power state. In the  
standby mode, temperature monitoring is disabled. The device will still respond to SMBus  
commands.  
3.2  
3.3  
One Shot During Standby Mode  
The EMC1053 supports a One-Shot command when it is in Standby Mode. Writing to the One-Shot  
register will cause the device to power up, perform 1 full set of temperature conversions, then return  
to Standby Mode.  
Operation During Run Mode  
When the device is active, there are two modes of operation available.  
„
Normal Mode (power-up default) - In this mode of operation, the EMC1053 continuously samples  
and updates all of its temperature channels.  
„
Hotter of Two Mode - In this mode, the EMC1053 continuously samples and then compares the  
two remote zones. The hotter of the two remote zones is loaded into the External Diode 2 Data  
Registers. In addition, the HOTTER bit in the Status register is set or cleared to indicate which  
external diode zone is hotter. If the two remote zones are exactly equal to each other, then the  
HOTTER bit is cleared (set to ‘0’), and the results of the two remote zones are stored in their  
respective registers.  
SMSC EMC1053  
Revision 1.37 (02-05-07)  
DATAS11HEET