欢迎访问ic37.com |
会员登录 免费注册
发布采购

EMC1403-3-AIZL-TR 参数 Datasheet PDF下载

EMC1403-3-AIZL-TR图片预览
型号: EMC1403-3-AIZL-TR
PDF下载: 下载PDF文件 查看货源
内容描述: [Serial Switch/Digital Sensor, 11 Bit(s), 2Cel, Square, Surface Mount, 3 X 3 MM, 0.50 MM PITCH, ROHS COMPLIANT, MO-187, MSOP-10]
分类和应用: 输出元件传感器换能器
文件页数/大小: 54 页 / 497 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第7页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第8页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第9页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第10页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第12页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第13页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第14页浏览型号EMC1403-3-AIZL-TR的Datasheet PDF文件第15页  
1°C Temperature Sensor with Beta Compensation  
Datasheet  
Chapter 3 Electrical Specifications  
3.1  
Absolute Maximum Ratings  
Table 3.1 Absolute Maximum Ratings  
DESCRIPTION  
RATING  
UNIT  
Supply Voltage (VDD  
)
-0.3 to 4.0  
-0.3 to 5.5  
V
V
Voltage on 5V tolerant pins (V5VT_pin  
)
Voltage on 5V tolerant pins (|V5VT_pin - VDD|) (see Note 3.1)  
Voltage on any other pin to Ground  
Operating Temperature Range  
-0.3 to 3.6  
V
-0.3 to VDD +0.3  
-40 to +125  
V
°C  
°C  
Storage Temperature Range  
-55 to +150  
Lead Temperature Range  
Refer to JEDEC Spec. J-STD-020  
Package Thermal Characteristics for MSOP-10  
Thermal Resistance (θj-a  
Package Thermal Characteristics for SOIC-14  
Thermal Resistance (θj-a  
Package Thermal Characteristics for DFN-10  
)
132.2  
77.7  
°C/W  
°C/W  
)
Thermal Resistance (θj-a  
)
77.1  
°C/W  
V
ESD Rating, All pins HBM  
2000  
Note: Stresses at or above those listed could cause permanent damage to the device. This is a stress  
rating only and functional operation of the device at any other condition above those indicated  
in the operation sections of this specification is not implied. When powering this device from  
laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be  
exceeded or device failure can result. Some power supplies exhibit voltage spikes on their  
outputs when the AC power is switched on or off. In addition, voltage transients on the AC  
power line may appear on the DC output. If this possibility exists, it is suggested that a clamp  
circuit be used.  
Note 3.1 For the 5V tolerant pins that have a pull-up resistor (SMCLK, SMDATA, THERM, and  
ALERT), the pull-up voltage must not exceed 3.6V when the device is unpowered.  
SMSC EMC1403/EMC1404  
Revision 2.0 (08-10-12)  
DATA1S1HEET  
 
 
 
 
 
 复制成功!