6 Channel Capacitive Touch Sensor with 6 LED Drivers
Datasheet
‘1’ - The LED6 pin is a push-pull output. When driving a logic ‘1’ the pin is driven high. When driving
a logic ‘0’ the pin is driven low.
Bit 4 - LED5_OT - Determines the output type of the LED5 pin.
Bit 3 - LED4_OT - Determines the output type of the LED4 pin.
Bit 2 - LED3_OT - Determines the output type of the LED3 pin.
Bit 1 - LED2_OT - Determines the output type of the LED2 pin.
Bit 0 - LED1_OT - Determines the output type of the LED1 pin.
5.24 Sensor LED Linking Register
Table 5.38 Sensor LED Linking Register
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
Sensor LED
Linking
CS6_
LED6
CS5_
LED5
CS4_
LED4
CS3_
LED3
CS2_
LED2
CS1_
LED1
72h
R/W
-
-
00h
The Sensor LED Linking registers control whether a Capacitive Touch Sensor is linked to an LED
output or not. If the corresponding bit is set, then the appropriate LED output will change states defined
by the LED Behavior controls (see Section 5.27) in response to the Capacitive Touch sensor.
Bit 5 - CS6_LED6 - Links the LED6 output to a detected touch on the CS6 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
‘0’ (default) - The LED6 output is not associated with a the CS6 input. If a touch is detected on the
CS6 input, then the LED will not automatically be actuated. The LED is enabled and controlled via
the LED Output Configuration register (see Section 5.24) and the LED Behavior registers (see
Section 5.27).
‘1’ - The LED6 output is associated with the CS6 input. If a touch is detected on the CS6 input
then the LED will be actuated and behave as defined in Table 5.43.
Bit 4 - CS5_LED5 - Links the LED5 output to a detected touch on the CS5 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
Bit 3 - CS4_LED4 - Links the LED4 output to a detected touch on the CS4 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
Bit 2 - CS3_LED3 - Links the LED3 output to a detected touch on the CS3 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
Bit 1 - CS2_LED2 - Links the LED2 output to a detected touch on the CS2 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
Bit 0 - CS1_LED1 - Links the LED1 output to a detected touch on the CS1 sensor. When a touch is
detected, the LED is actuated and will behave as determined by the LED Behavior controls.
5.25 LED Polarity Register
Table 5.39 LED Polarity Register
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
LED6_
POL
LED5_
POL
LED4_
POL
LED3_
POL
LED2_
POL
LED1_
POL
73h
R/W
LED Polarity
-
-
00h
SMSC CAP1066
Revision 1.1 (08-05-09)
DATA5S3HEET
SMSC [ SMSC CORPORATION ]
