欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAP1014-1-EZK-TR 参数 Datasheet PDF下载

CAP1014-1-EZK-TR图片预览
型号: CAP1014-1-EZK-TR
PDF下载: 下载PDF文件 查看货源
内容描述: 多通道电容式触摸传感器和LED驱动器 [Multiple Channel Capacitive Touch Sensor and LED Driver]
分类和应用: 驱动器传感器
文件页数/大小: 84 页 / 1205 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第33页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第34页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第35页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第36页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第38页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第39页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第40页浏览型号CAP1014-1-EZK-TR的Datasheet PDF文件第41页  
Multiple Channel Capacitive Touch Sensor and LED Driver  
Datasheet  
Table 5.5 Build History  
BUILD  
DEVICE  
REASON FOR CHANGE  
10h  
11h  
CAP1014  
Initial Development  
CAP1014-1  
Activated Lid Closure circuitry  
Activated Lid Closure circuitry and changed SMBus  
address to 0101_100b  
12h  
CAP1014-2  
5.4  
Slider Position / Volumetric Data Register  
Table 5.6 Slider Position / Volumetric Data Register  
ADDR  
06h  
R/W  
REGISTER  
B7  
B6  
B5  
B4  
B3  
B2  
B1  
B0  
DEFAULT  
R-C /  
R/W  
Slider Position /  
Volumetric Data  
-
POS[6:0]  
00h  
The Slider Position register indicates the absolute position of a Tap, Slide, or Press and Hold event  
detected on the Grouped sensors (slider). Alternately, the register stores volumetric data that increases  
or decreased based on detected operations on the Grouped sensors (slider).  
Bits 6-0 - POS[6:0] - Indicate absolute position or volumetric data as determined by the POS_VOL bit  
(see Section 5.14).  
5.4.1  
Absolute Position  
The absolute position of a single touch is available from this register. By interpolating information from  
up to 3 adjacent buttons, 16 different positions are calculated by the CAP1014 from the center of one  
button to the center of each adjacent button. The bits will encode a range from 2 to 98 indicative of  
where the touch occurred. Table 5.7 shows an example of the settings assuming a single button is  
pressed.  
If a slide is detected on the Grouped sensors, then the POS[6:0] bits will indicate the most recently  
touched sensor (i.e. where the slide ended) however will not indicate where the slide originated.  
APPLICATION NOTE: The register will be cleared to a value of 00h when it is read. It will be set to a valid position  
when the next ALERT is generated. It will be updated at the respective repeat rate for a slide  
or press and hold event regardless of whether it has been read or not. Therefore, it will only  
show the position of the last touch detected at the time of the interrupt.  
Table 5.7 Example Slider Absolute Position Decode  
POS[6:0]  
TOUCH POSITION  
SETTINGS  
CS8  
CS9  
02h (2d)  
12h (18d)  
22h (34d)  
32h (50d)  
CS10  
CS11  
SMSC CAP1014  
Revision 1.65 (08-11-09)  
DATA3S7HEET