欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAP1005 参数 Datasheet PDF下载

CAP1005图片预览
型号: CAP1005
PDF下载: 下载PDF文件 查看货源
内容描述: 5和6通道电容式触摸传感器 [5 and 6 Channel Capacitive Touch Sensor]
分类和应用: 传感器
文件页数/大小: 53 页 / 736 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号CAP1005的Datasheet PDF文件第26页浏览型号CAP1005的Datasheet PDF文件第27页浏览型号CAP1005的Datasheet PDF文件第28页浏览型号CAP1005的Datasheet PDF文件第29页浏览型号CAP1005的Datasheet PDF文件第31页浏览型号CAP1005的Datasheet PDF文件第32页浏览型号CAP1005的Datasheet PDF文件第33页浏览型号CAP1005的Datasheet PDF文件第34页  
5 and 6 Channel Capacitive Touch Sensor  
Datasheet  
„
‘1’ - A touch has been detected on one or more channels and the interrupt has been asserted.  
5.2  
Status Registers  
Table 5.3 Status Registers  
ADDR  
R/W  
REGISTER  
B7  
B6  
B5  
B4  
B3  
B2  
B1  
B0  
DEFAULT  
03h  
R
Sensor Status  
-
-
CS6  
CS5  
CS4  
CS3  
CS2  
CS1  
00h  
The Sensor Status Registers store status bits that indicate a touch has been detected. A value of ‘0’  
in any bit indicates that no touch has been detected. A value of ‘1’ in any bit indicates that a touch  
has been detected.  
All status bits are cleared when the device enters the Deep Sleep (DSLEEP = ‘1’ - see Section 5.1).  
All status bits are cleared when the INT bit is cleared and if a touch on the respective Capacitive Touch  
Sensor is no longer present. If a touch is still detected, then the bits will not be cleared (but this will  
not cause the interrupt to be asserted - see Section 5.6).  
Bit 5 - CS6 - Indicates that a touch was detected on Sensor 6.  
Bit 4 - CS5 - Indicates that a touch was detected on Sensor 5.  
Bit 3 - CS4 - Indicates that a touch was detected on Sensor 4.  
Bit 2 - CS3 - Indicates that a touch was detected on Sensor 3.  
Bit 1 - CS2 - Indicates that a touch was detected on Sensor 2.  
Bit 0 - CS1 - Indicates that a touch was detected on Sensor 1.  
5.3  
Noise Flag Status Registers  
Table 5.4 Noise Flag Status Registers  
ADDR  
R/W  
REGISTER  
B7  
B6  
B5  
B4  
B3  
B2  
B1  
B0  
DEFAULT  
-
-
CS6_  
NOISE  
CS5_  
NOISE  
CS4_  
NOISE  
CS3_  
NOISE  
CS2_  
NOISE  
CS1_  
NOISE  
0Ah  
R
Noise Flag Status  
00h  
The Noise Flag Status registers store status bits that are generated from the analog block if the  
detected noise is above the operating region of the analog detector. These bits indicate that the most  
recently received data from the sensor is invalid and should not be used for touch detection.  
Furthermore, so long as the bit is set for a particular channel, no decisions are made with the data. A  
touch is not detected, and a release is not detected.  
These bits are not sticky and will be cleared automatically if the analog block does not report a noise  
error.  
Revision 1.1 (08-05-09)  
SMSC CAP1005 / CAP1006  
DATA3S0HEET