欢迎访问ic37.com |
会员登录 免费注册
发布采购

AS2702AT 参数 Datasheet PDF下载

AS2702AT图片预览
型号: AS2702AT
PDF下载: 下载PDF文件 查看货源
内容描述: [Regulator, 1 Output, BIPolar,]
分类和应用:
文件页数/大小: 9 页 / 145 K
品牌: SIPEX [ SIPEX CORPORATION ]
 浏览型号AS2702AT的Datasheet PDF文件第1页浏览型号AS2702AT的Datasheet PDF文件第2页浏览型号AS2702AT的Datasheet PDF文件第4页浏览型号AS2702AT的Datasheet PDF文件第5页浏览型号AS2702AT的Datasheet PDF文件第6页浏览型号AS2702AT的Datasheet PDF文件第7页浏览型号AS2702AT的Datasheet PDF文件第8页浏览型号AS2702AT的Datasheet PDF文件第9页  
AS2700/01/02  
ELECTRICAL CHARACTERISTICS at V = V + 5V, I = 700mA, C = 22 F, unless otherwise specified. Limits in  
µ
O
O
Boldface type apply over the entire operating temperatuINre range. All Oother specifications are TA = 25°C.  
Parameter  
Conditions  
Typ.  
AS2700/01/02A  
AS2700/01/02B  
Max  
Units  
Min Max Min  
Error Comparator  
Output Leakage Current  
Output Low Voltage  
Upper Threshold Voltage  
Lower Threshold Voltage  
Hysteresis  
VOH = 30V  
0.01  
150  
60  
1.00  
2.00  
250  
400  
1.00  
2.00  
250  
400  
µA  
mV  
mV  
mV  
mV  
VIN = 4.5V  
IOL = 400µA  
(Note 8)  
40  
25  
40  
25  
(Note 8)  
(Note 8)  
75  
95  
95  
140  
140  
15  
Shutdown Input  
Input Logic Voltage  
Low (Regulator ON)  
High (Regulator OFF)  
VS = 2.4V  
0.7  
0.7  
V
2.0  
2.0  
Shutdown Pin Input Current  
30  
50  
90  
150  
800  
1000  
15  
µA  
100  
600  
750  
VS = 30V  
450  
3
Regulator Output Current In  
Shutdown  
10  
20  
µA  
25  
Note 1: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range.  
Note 2: Unless otherwise specified all limits are guaranteed for Tj = 25°C, VIN = 6V, IL = 100µA and CL = 1µF. Additional conditions for the 8-pin versions are  
feedback tied to 5V tap and output tied to output sense (VOUT = 5V) and VSHUTDOWN 0.8V.  
Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are  
covered under the specification for thermal regulation.  
Note 4: Line regulation for the AS2700/01/02 is tested at 150°C for IL = 1 mA. For IL = 100µA and TJ = 125°C, line regulation is guaranteed by design to 0.2%. See  
typical performance characteristics for line regulation versus temperature and load current.  
Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V differential at  
very low values of programmed output voltage, the minimum input supply voltage of 2V ( 2.3V over temperature) must be taken into account.  
Note 6: VREF VOUT (Vin - 1V), 2.3 Vin30V, 100µAIL250 mA, TJ TJMAX  
.
Note 7: Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage measured at 6V input. To  
express these thresholds in terms of output voltage change, multiply by the error amplifier gain = VOUT/VREF = (R1 + R2)/R2. For example, at a programmed output  
voltage of 5V, the Error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain constant as a percent of VOUT as  
V
OUT is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.  
Note 8: VSHUTDOWN 2V, VIN 30V, VOUT =0, Feedback pin tied to 5V Tap.  
Note 9: The junction -to-ambient thermal resistance of the TO-92 package is 180°C/ W with 0.4” leads and 160°C/ W with 0.25” leads to a PC board.  
The thermal resistance of the 8-Pin DIP package is 105°C/W junction-to-ambient when soldered directly to a PC board. Junction-to-ambient thermal resistance for the  
SOIC (S) package is 160°
UNREGULATED DC  
5V @ 700mA  
MAX  
+
INPUT  
FEEDBACK  
OUTPUT  
SENSE  
5V TAP  
180k ..  
+
_
ERROR  
AMPLIFIER  
FROM  
CMOS OR  
TTL  
330k..  
SHUTDOWN  
+
60k ..  
µ
1
F..  
+
+
_
______  
60 mV  
ERROR  
ERROR DETECTION  
COMPARATOR  
TO CMOS OR  
TTL  
1.23V  
+
REFERENCE  
GROUND  
AS2700/01/02 Block Diagram  
Rev. 10/11/00