欢迎访问ic37.com |
会员登录 免费注册
发布采购

SC91314A 参数 Datasheet PDF下载

SC91314A图片预览
型号: SC91314A
PDF下载: 下载PDF文件 查看货源
内容描述: 与重拨功能音频/脉冲拨号器 [TONE / PULSE DIALER WITH REDIAL FUNCTION]
分类和应用: 脉冲
文件页数/大小: 14 页 / 118 K
品牌: SILAN [ SILAN MICROELECTRONICS JOINT-STOCK ]
 浏览型号SC91314A的Datasheet PDF文件第1页浏览型号SC91314A的Datasheet PDF文件第2页浏览型号SC91314A的Datasheet PDF文件第3页浏览型号SC91314A的Datasheet PDF文件第4页浏览型号SC91314A的Datasheet PDF文件第6页浏览型号SC91314A的Datasheet PDF文件第7页浏览型号SC91314A的Datasheet PDF文件第8页浏览型号SC91314A的Datasheet PDF文件第9页  
Silan  
Semiconductors  
SC91310 Series  
PIN DESCRIPTION  
Pin No.  
Pin Na me  
I/O  
De sc ription  
The keyboard input may be from either the standard 4x4 keyboard or an  
inexpensive single contact (form A) keyboard. Electronic input from a µC can  
also be used. A valid key entry is defined as a single row being connected to a  
single column.  
1~4  
&
Column-  
I
Row Inputs  
15~18  
A built-in inverter provides oscillation with an inexpensive 3.579545 MHz crystal  
or ceramic resonator.  
XT,  
XT  
7,8  
9
I,O  
O
The T/P  
is a conventional CMOS N-channel open drain output. The  
MUTE  
T/P  
MUTE  
output transistor is switched on during pulse and tone mode dialing sequence  
and flash break. Otherwise, it is switched off.  
Pulling mode pin to Vss places the dialer in tone mode. Pulling mode pin to VDD  
places the dialer in pulse mode (10 pps). Leaving mode pin floating places the  
dialer in pulse mode (20 pps).  
13  
MODE  
I
Hook switch input.  
= 1: On-hook state. Chip in sleeping mode, no  
HKS  
operation.  
= 0: Off-hook state. Chip enabled for normal operation. The  
HKS  
DP  
HKS  
10  
11  
O
O
pin is pulled to VDD by an internal resistor.  
HKS  
N-channel drain dialing pulse output (Figure 1). Flash key will cause  
active in both pulse mode and tone mode.  
to go  
DP  
In pulse mode, remains in low state at all times. In tone mode, outputs a dual or  
single tone. Detailed timing diagram for tone mode is shown in Figure 2(a, b).  
Output Frequency(Hz)  
Specified  
697  
Actual  
699  
Error %  
+0.28  
-0.52  
R1  
12  
DTMF  
O
R2  
770  
766  
R3  
852  
848  
-0.47  
R4  
941  
948  
+0.74  
+0.57  
-0.30  
C1  
1209  
1336  
1477  
1216  
1332  
1472  
C2  
C3  
-0.34  
14,6  
5
VDD, Vss  
B/M  
I
I
Power input pins.  
The break make ratio is 60:40 if /M = 1 and is 66.6:33.3 if B/M = 0. This pin has  
no function in DTMF mode.  
HANGZHOU SILAN MICROELECTRONICS CO.,LTD.  
Rev: 2.1  
2002.12.03  
5