GP1A05/GP1A22LC/GP1A23LC/GP1A25LC
■ Recommended Connectors on the Inserted Side
Recommended connectors on the inserted side forGP1A05,GP1A22LC, and GP1A23LCare shown below.
<<GP1A05>>
● JAPAN AMP made El series connectors
● JAPAN AMP made El series connectors
(
)
(
)
low profile type
standard type
Natural
color
Natural
color
Housing color
Black
Blue Green
Red
Housing color
Black
Blue Green
Red
Housing Model No. 171822-3 2-171822-3 4-171822-3 6-171822-3 8-171822-3
Housing Model No. 172142-3 2-172142-3 4-172142-3 6-172142-3 8-172142-3
AWG
size
Product
shape
AWG
size
Special
terminal
Model. No.
Material Model No.
Brass 170204-1
Product shape
Model No.
Bulk
Chain
Bulk
170369-1
170354-1
170370-1
170355-1
AWG
26 to 22
Bulk
Chain
Bulk
Copper
(
Material:
170204-2
phosphide
AWG
26 to 20
Copper
phosphide
AWG
30 to 26
)
Brass 170262-1
Chain
Special
terminal
Model. No.
Copper
170262-2
phosphide
● JAPAN AMP made El series connectors
(
)
Brass 170205-1
amp mass termination
Copper
AWG26
AWG28
AWG24 AWG22
(
Housing-terminal
united type
connector
170205-2
phosphide
(
Natural
AWG
30 to 26
(
)
)
(
)
Green
Black
Red
)
color
Brass 170263-1
172054-3 172053-3 172052-3 172051-3
Chain
Copper
170263-2
phosphide
* Terminal Material : Copper phosphide
<<GP1A22LC/ GP1A23LC>>
● JAPAN SOLDERLESS TERMINAL MSG. CO., LTD. made Natural color •bulk
(
)
Housing Model No.
H3P-SHF-AA
S3P-SHF-1
AWG
size
AWG
size
Material
Model No.
Material
Brass
Model No.
Brass
SHF-001T-0.8SS
SHF-001T-0.8BS
SHF-002T-0.8SS
SHF-001T-0.8BS
SHF-001T-0.8P
AWG
26 to 22
AWG
27 to 22
Special
terminal
Model. No.
Copper
phosphide
Copper
phosphide
-
Brass
Brass
SHF-002T-0.8P
AWG
30 to 26
AWG
30 to 28
Copper
phosphide
Copper
phosphide
-
■ Precautions for Use
( )
1 It is recommended that a by-pass capacitor of more than 0.01 µ F be added betw een VCC and GND
near the device in order to stabilize power supply line.
( )
2 In this product, the PWB is fixed with a rear cover, and cleaning solvent may remain inside the
case; therefore, dip cleaning or ultrasonic cleaning is prohibited.
( )
3 Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent.
However, do not perform the above cleaning using a soft cloth with cleaning solvent in the
marking portion.
In this case, use only the following type of cleaning solvent used for wiping off:
Ethyl alcohol, Methyl alcohol, Isopropyl alcohol,
When the cleaning solvents except for specified materials are used, please consult us.
( )
4 As for other general cautions, refer to the chapter “Precautions for Use ”.
SHARP [ SHARP ELECTRIONIC COMPONENTS ]
