REVISION W
DO NOT
SCALE FROM
THIS PRINT
.397 10.08
02
(No OF POS x .100[2.54])
+ .694[17.63] REF
(No OF POS -1)
x .100[2.54] REF
.150 3.81 (TYP)
REF
No OF POSITIONS
-05 THRU -25
EJH-1XX-XX-XX-D-XX-XX-XX
OPTION
-LC: LOCKING CLIP (FOR -SM ONLY)
(SEE NOTE 10)
-P: PICK & PLACE PAD (FOR -SM ONLY)
(USE PPP-50, SEE FIGURE 6, SHEET 3)
-K: POLYAMIDE FILM (SEE FIG 3, SHEET 3)
(USE K-850-650)
-TR: TAPE & REEL PACKAGING
(SEE FIG 7, SHEET 3))
(FOR -SM-P, & -SM-K ONLY)
(NOT AVAILABLE ON -SM-LC)
(NOT AVAILABLE ON -25 POSITION)
"A"
.100 2.54
.020 0.51 REF
.390 9.91 REF
01
2 MAX SWAY
(TYP)
(No OF POS x .100[2.54])
+ .104[2.64] REF
EJH-XX-D
.025 0.64 SQ REF
.225 5.72
REF
"A"
.250 6.35 REF
-01: STANDARD
(USE EJH-XX-D)
-02: EXTENDED
(SEE FIG 11, SHEET 4)
(USE EJH-XX-D-EXT &
EHA-03-EXT)
LEAD STYLE
PLATING SPECIFICATION
-S: SELECTIVE GOLD
(USE T-1S6X-XX-S-X)
-F: FLASH SELECTIVE GOLD
(USE T-1S6X-XX-F-X)
-SM: SELECTIVE HEAVY GOLD
(USE T-1S6X-XX-S-X)
-FM: FLASH SELECTIVE GOLD,
MATTE TIN TAIL
(USE T-1S6X-XX-F-X)
-L : LIGHT SELECTIVE GOLD
MATTE TIN TAIL
(USE T-1S6X-XX-L-X)
POLARIZED OPTION
-XX = PIN OMITED
TAIL OPTION
-SM: SURFACE MOUNT (SEE FIG. 1)
-TH: THROUGH HOLE (SEE FIG 8, SHEET 2)
-RA: RIGHT ANGLE (SEE FIG 9, SHEET 2)
ROW SPECIFICATION
-D: DOUBLE
.500 12.70 REF
90°
.505 12.83
.004[.10]
.467±.010 11.86±0.25
SECTION "A"-"A"
PIN A (SEE TABLE 1)
(No OF POS x .100[2.54])
+ .400[10.16] REF
.060 1.52
LC-09-TM
.060 1.52 REF
90°
.130 3.30
.280 7.11
POSITION 1 INDICATOR
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY TO BE: .004 MAX FOR POSITIONS -05 THRU -10
.006 MAX FOR POSITIONS -15 THRU -25
3. BURR ALLOWANCE: .0015 MAX.
4. MINIMUM PUSHOUT FORCE: 1 LB MIN.
5. MAXIMUM ALLOWABLE BOW: .002 INCH/INCH AFTER ASSEMBLY.
6. PARTS TO BE TUBED WITH EJECTOR ARMS IN THE UP POSITION
AS SHOWN.
7. REPRESS TO DIMENSION SHOWN.
8. NOTE DELETED.
9. MEASURE FROM THE TIPS OF THE TERMINALS.
10. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC
OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC
RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH
THE –LC OPTION.
FIG 1
EJH-110-01-X-D-SM-LC SHOWN
.467±.010 11.86±0.25
-SM IN-PROCESS 1
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
-SM IN-PROCESS 2
PROPRIETARY NOTE
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
ANGLES
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
MATERIAL:
DO NOT SCALE DRAWING
-01 INSULATOR: VECTRA E130i, COLOR: BLACK
-02 INSULATOR COLOR: NATURAL
TERMINAL: PHOS BRONZE 510 3/4 HARD
F:\DWG\MISC\MKTG\EJH-1XX-XX-XX-D-XX-XX-XX-MKT.SLDDRW
SHEET SCALE: 1:0.666667
DESCRIPTION:
.100 x .100 EJECTOR HEADER ASSEMBLY
DWG. NO.
BY:
ERIC M.
EJH-1XX-XX-XX-D-XX-XX-XX
09/19/01
SHEET
1
OF
4
SAMTEC [ Samtec, Inc ]
