SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25
O
C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
1
Calibration Tolerance
Frequency Stability
Over Temperature
Total Tolerance
2
Supply Current (Typical)
3.3 V ± 10%
5.0 V ± 10%
± 50 ppm, or tighter as required
± 100 ppm for 25
O
C to 150
O
C
± 150 ppm for 25
O
C to 175
O
C
± 175 ppm for 25
O
C to 200
O
C
± 200 ppm for 25
O
C to 200
O
C
3.3 V
3.0 mA
5.0 mA
6.0 mA
23.0 mA
5.0 V
8.0 mA
10.0 mA
14.0 mA
39.0 mA
Supply Voltage V
DD
Storage Temperature
Maximum Process Temperature
-0.3 V to 7.0 V
-55
O
C to 125
O
C
260
O
C, 20 seconds
ENABLE/DISABLE OPTIONS (E/T/N)
24 MHz
32 MHz
50 MHz
120 MHz
Output Load (CMOS)
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
Aging, first year
10 ppm MAX at 25
O
C
Aging, 1,000 Hrs
100 ppm MAX at 200
O
C
Shock, survival
3
Std: 3,000 g, 0.3 ms,
1
/
2
sine
HG: 10,000 g, 0.3 ms,
1
/
2
sine
20 g, 10-2,000 Hz swept sine
Vibration, survival
4
Operating Temp Range -55
O
C up to 200
O
C
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the T-version.
So, the E-version offers very low current consumption
when the oscillator is disabled and the T-version offers very
fast output recovery when the oscillator is re-enabled. The
N-version does not have PIN 1 connected internally and so
has no enable/disable capability. The following table
summarizes the three options.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
E
T
When enabled (PIN 1 is high*)
Output
Oscillator
Current consumption
Freq. output
Oscillates
Normal
Freq. output
Oscillates
Normal
When disabled (PIN 1 is low)
Output
High Z state
Stops
Very low
High Z state
Oscillates
Lower than normal
1. All frequencies, voltages, temperature ranges and enable/disable options may not be
available. Contact factory.
2. Total Tolerance = Calibration Tolerance + Frequency Stability over temperature.
3. For non-high-shock CXOHT and CXOMHT oscillators only. The specification for
CXOXHT oscillators is 5,000 g, 0.3 ms, 1
/
2 sine.
4. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing available.
Note: All parameters are measured at ambient temperature with a 10 M!, 15 pF load.
Oscillator
Current consumption
When re-enabled (PIN 1 changes from low to high)
Output recovery
Delayed
Immediate
PACKAGING OPTIONS
*
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
CXOHT, CXOMHT, CXOXHT - Tray Pack
- 16 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet # 10109)
HOW TO ORDER CXOHT, CXOMHT and CXOXHT OSCILLATORS
CXOMHT
CXOHT
CXOMHT
CXOXHT
Supply Voltage
4 = 3.3 V
5 = 5.0 V
4
S
“S” if special or
custom design.
Blank if Std.
E
Enable/Disable
Option E or T
or N
SM3
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
20.0M,
Frequency
M = MHz
K = kHz
Calibration
Tolerance
@ 25
0
C
(in ppm)
/
/ 200
Total Frequency
Tolerance (in
ppm)
/
H
Temp. Range:
H = 25
0
C to 200
0
C
S = Customer
Specified Temp.
Range
HG = High Shock
otherwise leave
blank.
OR
25
Calibration
Tolerance
@ 25
0
C
(in ppm)
Frequency
Stability over
Temp. Range
(in ppm)
/
175
/
Total
Frequency
Tolerance
(in ppm)
/
H
Temp. Range:
H = 25
0
C to
200
0
C
S = Customer
Specified Temp.
Range
Frequency
Stability over
Temp. Range
(in ppm)
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de
www.rsg-electronic.de
■
■
■
■
■
Änderungen vorbehalten / subject to change without notice
RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
