SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25
O
C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
1
Calibration Tolerance
Frequency Stability
Over Temperature
3
Supply Current (Typical)
2
Supply Voltage V
DD
-0.5V to 7.0V
Storage Temperature
-55
O
C to +125
O
C
Maximum Process Temperature 260
O
C fo 20 seconds
ENABLE/DISABLE OPTIONS (E/T/N)
5.0 V
+
_
+
_
+
_
100 ppm
50 ppm for Commercial
100 ppm for Industrial
+
_
100 ppm for Military
10 MHz
4 mA
24 MHz
8 mA
30 MHz 10 mA
40 MHz 12 mA
50 MHz 14 mA
15 pF
5 ms MAX
6 ns MAX
40% MIN, 60% MAX
10 ppm MAX
10,000 g, 0.3 ms,
1
/
2
sine
20 g, 10-2,000 Hz swept sine
Output Load (CMOS)
4
Start-up Time
Rise/Fall Time
Duty Cycle
Aging, first year
Shock, survival
5
Vibration, survival
6
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table compares the E and T
versions.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
E
When enabled (PIN 1 is high*)
Output
Oscillator
Current consumption
When disabled (PIN 1 is low)
Output
Oscillator
Current consumption
High Z state
Stops
Very low
Freq. output
Oscillates
Normal
T
Operating Temp Ranges -10
O
C to +70
O
C (Commercial)
-40
O
C to +85
O
C (Industrial)
-55
O
C to +125
O
C (Military)
1. Other voltages available. For 3.3 V, see CXO3MHG data sheet. For others,
contact factory.
2. Other tolerances available.
3. Does not include calibration tolerance. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. Higher shock version available. Contact factory for requirements above 10,000 g.
6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
Freq. output
Oscillates
Normal
High Z state
Oscillates
Lower than normal
When re-enabled (PIN 1 changes from low to high)
Output recovery
Delayed
Immediate
PACKAGING OPTIONS
CXOMHG - Tray Pack
- 16 mm tape, 7˝or 13˝ reels
Per EIA 418
(see Tape and Reel data sheet 10109)
*
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
HOW TO ORDER CXOMHG SURFACE MOUNT CRYSTAL OSCILLATORS
CXOMHG
S
“S” if special or
custom design.
Blank if Std.
T
Enable/Disable
Option
E, T, or N
SM3
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
32.0M
Frequency
K = kHz
M = MHz
,
100
Calibration
Tolerance
@ 25
0
C
(in ppm)
/
100
/
I
Temp. Range:
C = -10
O
C to +70
O
C
I
= -40
O
C to +85
O
C
M = -55
O
C to +125
O
C
S = Customer Specified
Frequency
Stability over
Temp.Range
(in ppm)
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de
www.rsg-electronic.de
■
■
■
■
■
Temp. Range:
C = -10
O
C to +70
O
C
I
= -40
O
C to +85
O
C
M = -55
O
C to +125
O
C
S = Customer Specified
10160 Rev A
S
YS
TEM
C
ERT
I
F
I
C
AT
N
IO
Änderungen vorbehalten / subject to change without notice
01
Pb
IS
O
90
RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
