FN SUFFIX
CASE 777-02
Plastic Package
(PLCC)
M
S
S
0.007(0.180)
T
L–M
N
B
M
S
S
0.007(0.180)
T
L–M
N
U
1
ISSUE C
D
–N–
Z
Y BRK
–M–
–L–
X
G1
S
S
S
0.010 (0.25)
T
L–M
N
VIEW D–D
H
V
W
D
M
S
S
0.007(0.180)
T
L–M
N
44
1
M
M
S
S
S
S
A
R
0.007(0.180)
0.007(0.180)
T
T
L–M
L–M
N
N
K1
Z
K
J
C
F
E
M
S
S
0.007(0.180)
VIEW S
T
L–M
N
0.004 (0.10)
G
SEATING
PLANE
–T–
INCHES
DIM MIN MAX
MILLIMETERS
MIN MAX
G1
VIEW S
A
B
C
E
0.685 0.695 17.40 17.65
0.685 0.695 17.40 17.65
S
S
S
0.010 (0.25)
T
L–M
N
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
4.20
2.29
0.33
4.57
2.79
0.48
NOTES:
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE
TOP AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
F
1. DATUMS –L–, –M–, AND –N– ARE DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010
(0.25) PER SIDE.
G
H
J
1.27 BSC
0.026 0.032
0.66
0.51
0.64
0.81
–––
–––
0.020
0.025
–––
–––
K
R
U
V
W
X
Y
Z
0.650 0.656 16.51 16.66
0.650 0.656 16.51 16.66
0.042 0.048
0.042 0.048
0.042 0.056
––– 0.020
1.07
1.07
1.07
–––
2
1.21
1.21
1.42
0.50
10
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
2
10
G1 0.610 0.630 15.50 16.00
K1 0.040 ––– 1.02 –––
NOTES:
M SUFFIX
CASE 803C
PRELIMINARY
Plastic Package
6
DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
–A–
7
8
CONTROLLING DIMENSION: MILLIMETER.
DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
–F–
9
MAXIMUM MOLD PROTRUSION 0.15 (0.008) PER
SIDE.
20
1
11
10
10 DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.006) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
K
–B–
1
J
20
G
MILLIMETERS
DIM MIN MAX
INCHES
MIN
MAX
0.504
0.215
0.081
0.020
0.032
S 10 PL
A
B
C
D
E
F
12.35
5.10
1.95
0.35
–––
12.80 0.486
5.45 0.201
2.05 0.077
0.50 0.014
M
M
0.13 (0.005)
B
N
0.81
12.40*
–––
0.488*
G
H
J
K
L
M
N
S
1.15
0.59
0.18
1.10
0.05
0
1.39 0.045
0.81 0.023
0.27 0.007
1.50 0.043
0.20 0.001
0.055
0.032
0.011
0.059
0.008
10
C
0.10 (0.004)
E
L
M
10
0
D 20 PL
–T–
SEATING
PLANE
0.50
7.40
0.85 0.020
8.20 0.291
0.033
0.323
M
S
S
0.13 (0.005)
T B
A
*APPROXIMATE
13–14
MOTOROLA ANALOG IC DEVICE DATA
ROCHESTER [ Rochester Electronics ]
