RT7257B
CIN and COUT Selection
Thermal Considerations
The input capacitance, CIN, is needed to filter the
trapezoidal current at the source of the high side MOSFET.
To prevent large ripple current, a low ESR input capacitor
sized for the maximum RMS current should be used. The
approximate RMS current is given :
For continuous operation, do not exceed the maximum
operation junction temperature 125°C. The maximum
power dissipation depends on the thermal resistance of
IC package, PCB layout, the rate of surroundings airflow
and temperature difference between junction to ambient.
The maximum power dissipation can be calculated by
following formula :
V
OUT
V
IN
I
= I
1
RMS
OUT(MAX)
V
IN
V
OUT
This formula has a maximum at VIN = 2VOUT, where
IRMS = IOUT/2. This simple worst case condition is
commonly used for design because even significant
deviations do not offer much relief. Choose a capacitor
rated at a higher temperature than required. Several
capacitors may also be paralleled to meet size or height
requirements in the design. For the input capacitor, two
10μF low ESR ceramic capacitors are Suggested. For
the Suggested capacitor, please refer to Table 3 for more
details. The selection of COUT is determined by the
required ESR to minimize voltage ripple. Moreover, the
amount of bulk capacitance is also a key for COUT selection
to ensure that the control loop is stable. Loop stability
can be checked by viewing the load transient response
as described in a later section.
PD(MAX) = (TJ(MAX) − TA ) / θJA
Where TJ(MAX) is the maximum operation junction
temperature , TA is the ambient temperature and the θJA is
the junction to ambient thermal resistance.
For recommended operating conditions specification, the
maximum junction temperature is 125°C. The junction to
ambient thermal resistance θJA is layout dependent. For
PSOP-8 package, the thermal resistance θJA is 75°C/W
on the standard JEDEC 51-7 four-layers thermal test board.
The maximum power dissipation at TA = 25°C can be
calculated by following formula :
PD(MAX) = (125°C − 25°C) / (75°C/W) = 1.333W
(min.copper area PCB layout)
PD(MAX) = (125°C − 25°C) / (49°C/W) = 2.04W
(70mm2copper area PCB layout)
The output ripple, ΔVOUT , is determined by :
1
The thermal resistance θJA of SOP-8 (Exposed Pad) is
determined by the package architecture design and the
PCB layout design. However, the package architecture
design had been designed. If possible, it's useful to
increase thermal performance by the PCB layout copper
design. The thermal resistance θJA can be decreased by
adding copper area under the exposed pad of SOP-8
(Exposed Pad) package.
VOUT I ESR
L
8fCOUT
The output ripple will be the highest at the maximum input
voltage since ΔIL increases with input voltage. Multiple
capacitors placed in parallel may be needed to meet the
ESR and RMS current handling requirement. Higher values,
lower cost ceramic capacitors are now becoming available
in smaller case sizes. Their high ripple current, high voltage
rating and low ESR make them ideal for switching regulator
applications. However, care must be taken when these
capacitors are used at input and output. When a ceramic
capacitor is used at the input and the power is supplied
by a wall adapter through long wires, a load step at the
output can induce ringing at the input, VIN. At best, this
ringing can couple to the output and be mistaken as loop
instability. At worst, a sudden inrush of current through
the long wires can potentially cause a voltage spike at
VIN large enough to damage the part.
As shown in Figure 7, the amount of copper area to which
the SOP-8 (Exposed Pad) is mounted affects thermal
performance. When mounted to the standard
SOP-8 (Exposed Pad) pad (Figure 7.a), θJA is 75°C/W.
Adding copper area of pad under the SOP-8 (Exposed
Pad) (Figure 7.b) reduces the θJA to 64°C/W. Even further,
increasing the copper area of pad to 70mm2 (Figure 7.e)
reduces the θJA to 49°C/W.
Copyright 2016 Richtek Technology Corporation. All rights reserved.
©
is a registered trademark of Richtek Technology Corporation.
DS7257B-04 October 2016
www.richtek.com
11