欢迎访问ic37.com |
会员登录 免费注册
发布采购

HIRK-433 参数 Datasheet PDF下载

HIRK-433图片预览
型号: HIRK-433
PDF下载: 下载PDF文件 查看货源
内容描述: RF接收解码器HYBRID [RF RECEIVER DECODER HYBRID]
分类和应用: 解码器
文件页数/大小: 10 页 / 173 K
品牌: RFSOLUTIONS [ RFSOLUTIONS.LTD ]
 浏览型号HIRK-433的Datasheet PDF文件第1页浏览型号HIRK-433的Datasheet PDF文件第2页浏览型号HIRK-433的Datasheet PDF文件第3页浏览型号HIRK-433的Datasheet PDF文件第5页浏览型号HIRK-433的Datasheet PDF文件第6页浏览型号HIRK-433的Datasheet PDF文件第7页浏览型号HIRK-433的Datasheet PDF文件第8页浏览型号HIRK-433的Datasheet PDF文件第9页  
RF R
ECEIVER
D
ECODER
H
YBRID
.
HiR6 Versions
HIRK-315
HIRK-433
HIR6-433
This range of modules provides a very low power SuperRegenerative receiver, combined with flash
programmable controller, supplied pre-programmed to operate with a suitable Keeloq Transmitter encoder.
The range from such a system can be up to 50 metres Line of Sight (LOS). The current consumption is
1.5mA however this may be reduced to only 1 – 2 uA by placing the device into sleep mode and turning off
the supply to the radio section. A supervisory processor can then wake the module from time to time to allow
it to check for the presence of radio data.
Custom versions of this product are available, please contact our sales department for further details
Pin Descriptions SuperRegenerative Versions (Hir6 series)
Pin No
1
2
3
7
11
13
14
15
16
17
18
19
20
21
22
23
24
25
Name
Vcc-RF
GND-RF
ANT
GND-RF
GND-AF
RSSI
O/P-AF
Vcc-digital
GND-digital
MCLR
Latch/ Mom
Serial Data
O/P1
Learn /
LED
O/P2
O/P3
O/P4
Run / Sleep
+5V Supply Voltage – RF section.
RF Ground.
Connect Antenna to this input.
RF Ground.
AF Ground.
Received Signal Strength Indicator (RSSI)
Raw Data output from RF receiver (CMOS/TTL signal)
+5V Supply Voltage – digital section.
AF Ground – digital section.
Pulls Microcontroller into reset if connected to Ground
May be left unconnected if not required (internally tied high)
Set High: Configures data outputs as latching. NOTE: no pull-up/down provided.
Set Low: Configures data outputs as momentary.
Serial data output
Active Low data Output 1 (has a 220Ω series resistor)
Dual function:
Programming Switch input, When grounded places the HiR6 into ‘Learn’ mode.
External LED output, Indicates data reception, and programming status.
(has a 1K5 series resistor)
Active Low data Output 2 (has a 220Ω series resistor)
Active Low data Output 3 (has a 220Ω series resistor)
Active Low data Output 4 (has a 220Ω series resistor)
Pulled high : HiR6 operating normally.
Pulled Low : HiR6 microcontroller enters sleep mode.
Description
DS010-6 May 06
©2006
REG No 277 4001, England.
Page 4