欢迎访问ic37.com |
会员登录 免费注册
发布采购

RF2516PCBA-410 参数 Datasheet PDF下载

RF2516PCBA-410图片预览
型号: RF2516PCBA-410
PDF下载: 下载PDF文件 查看货源
内容描述: VHF / UHF TRANSMIITER [VHF/UHF TRANSMIITER]
分类和应用:
文件页数/大小: 22 页 / 272 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号RF2516PCBA-410的Datasheet PDF文件第1页浏览型号RF2516PCBA-410的Datasheet PDF文件第2页浏览型号RF2516PCBA-410的Datasheet PDF文件第4页浏览型号RF2516PCBA-410的Datasheet PDF文件第5页浏览型号RF2516PCBA-410的Datasheet PDF文件第6页浏览型号RF2516PCBA-410的Datasheet PDF文件第7页浏览型号RF2516PCBA-410的Datasheet PDF文件第8页浏览型号RF2516PCBA-410的Datasheet PDF文件第9页  
RF2516  
Pin  
1
Function Description  
Interface Schematic  
This pin is connected directly to the reference oscillator transistor base.  
OSC B  
VCC  
The intended reference oscillator configuration is a modified Colpitts. A  
68pF capacitor should be connected between pin 1 and pin 2.  
OSC B  
OSC E  
This pin is connected directly to the emitter of the reference oscillator  
transistor. A 33pF capacitor should be connected from this pin to  
ground.  
See pin 1.  
2
3
OSC E  
PD  
VCC  
Power Down control for all circuitry. When this pin is a logic “low” all cir-  
cuits are turned off. When this pin is a logic “high”, all circuits are oper-  
ating normally. A high” is V . Diodes shown in the interface  
schematic provide 3kV electrostatic discharge (ESD) protection using  
the human body model.  
CC  
PD  
Ground connection for the TX OUT amp. Keep traces physically short  
and connect immediately to ground plane for best performance. Diodes  
shown in the interface schematic provide 3kV electrostatic discharge  
(ESD) protection using the human body model.  
4
5
GND  
Transmitter output. This output is an open collector and requires a pull-  
up inductor for bias/matching and a tapped capacitor for matching.  
TXOUT  
TX OUT  
RF IN  
MOD IN  
Ground connection for the TX output buffer amplifier. Diodes shown in  
the interface schematic provide 3kV electrostatic discharge (ESD) pro-  
tection using the human body model.  
6
7
GND1  
VCC1  
VCC  
This pin is used to supply bias to the TX buffer amplifier. Diodes shown  
in the interface schematic provide 3kV electrostatic discharge (ESD)  
protection using the human body model.  
VCC1  
AM analog or digital modulation can be imparted to the carrier by an  
input to this pin. An external resistor is used to bias the output amplifi-  
ers through this pin. The voltage at this pin must not exceed 1.1V.  
Higher voltages may damage the device. Diodes shown in the interface  
schematic provide 3kV electrostatic discharge (ESD) protection using  
the human body model.  
8
MOD IN  
VCC  
TX OUT  
1 kΩ  
MOD IN  
This pin is used to supply DC bias to the VCO, crystal oscillator, pre-  
scaler, phase detector, and charge pump. An IF bypass capacitor  
should be connected directly to this pin and returned to ground. Diodes  
shown in the interface schematic provide 3kV electrostatic discharge  
(ESD) protection using the human body model.  
See pin 7.  
9
VCC2  
GND2  
Digital PLL ground connection. Diodes shown in the interface sche-  
matic provide 3kV electrostatic discharge (ESD) protection using the  
human body model.  
10  
VCC  
GND  
Rev A17 060712  
11-3