欢迎访问ic37.com |
会员登录 免费注册
发布采购

RF2152 参数 Datasheet PDF下载

RF2152图片预览
型号: RF2152
PDF下载: 下载PDF文件 查看货源
内容描述: 双模CDMA / AMPS或TDMA / AMPS 3V功率放大器 [DUAL-MODE CDMA/AMPS OR TDMA/AMPS 3V POWER AMPLIFIER]
分类和应用: 放大器功率放大器
文件页数/大小: 12 页 / 253 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号RF2152的Datasheet PDF文件第1页浏览型号RF2152的Datasheet PDF文件第2页浏览型号RF2152的Datasheet PDF文件第4页浏览型号RF2152的Datasheet PDF文件第5页浏览型号RF2152的Datasheet PDF文件第6页浏览型号RF2152的Datasheet PDF文件第7页浏览型号RF2152的Datasheet PDF文件第8页浏览型号RF2152的Datasheet PDF文件第9页  
RF2152  
Pin  
1
Function Description  
Interface Schematic  
Power supply for input bias circuitry. A 100 pF high frequency bypass  
VCC  
capacitor is recommended.  
Interstage tuning. This pin will connect to a shunt inductor used for  
interstage tuning. For 824MHz to 849MHz a 1.5nH discrete inductor is  
used; for 877MHz to 925MHz a shorted transmission line presenting  
0.7 nH of inductance or discrete inductor may be used. This inductor  
should be placed as close to the pin as possible.  
2
LTUNE  
2
No connection. Grounding pin is recommended.  
3
4
NC  
VCC1  
Power supply for stage 1. V should be fed through a 25nH or greater See pin 6.  
CC  
inductor with a decoupling capacitor on the V side.  
CC  
Ground for stage 1. Keep traces physically short and connect immedi- See pin 6.  
ately to ground plane for best performance. This ground should be iso-  
lated from the backside ground contact.  
5
6
GND1  
RF IN  
RF input. An external DC blocking capacitor is required if this port is  
connected to a DC path to ground or a DC voltage.  
VCC1  
GND1  
RF IN  
From Bias  
Stages  
Power Down control. When this pin is “low”, all circuits are shut off.  
7
VPD  
When this pin is 2.8 volts, all circuits are operating normally. V  
PD  
requires a regulated 2.8 V for the amplifier to operate properly over all  
specified temperature and voltage ranges. A dropping resistor from a  
higher regulated voltage may be used to provide the required 2.8 V. A  
100 pF high frequency bypass capacitor is recommended.  
Connect to pin 7.  
8
9
10  
11  
12  
VPD  
NC  
NC  
NC  
RF OUT  
No connection. Grounding pin is recommended.  
No connection. Grounding pin is recommended.  
No connection. Grounding pin is recommended.  
RF output and power supply for the output stage. The bias for the out-  
put stage is provided through this pin and pin 13. An external matching  
network is required to provide the optimum load impedance; see the  
application schematics for details. The first shunt cap of the matching  
circuit should be placed as close to the pin as possible.  
RF OUT  
From Bias  
Stages  
Same as pin 12.  
See pin 12.  
13  
14  
RF OUT  
RF OUT  
Harmonic trap. This pin connects to the RF output but is used for pro-  
viding a low impedance to the second harmonic of the operating fre-  
quency. An inductor or transmission line resonating with a shunt  
See pin 12.  
capacitor at 2f is connected to this pin.  
0
No connection. Grounding pin is recommended.  
15  
16  
NC  
MODE  
The mode pin allows higher efficiency operation in AMPS and low  
power CDMA modes. MODE should be set “low” for highest efficiency  
in AMPS/TACS and in low power (<+15 dBm) CDMA operation. MODE  
should be set “high” for best linearity in high power CDMA operation.  
MODE  
Ground connection. The backside of the package should be soldered to  
a top side ground pad which is connected to the ground plane with mul-  
tiple vias. The pad should have a short thermal path to the ground  
plane.  
Pkg  
Base  
GND  
Rev A8 001109  
2-157