欢迎访问ic37.com |
会员登录 免费注册
发布采购

NBB-312_1 参数 Datasheet PDF下载

NBB-312_1图片预览
型号: NBB-312_1
PDF下载: 下载PDF文件 查看货源
内容描述: 级联宽带的GaAs MMIC放大器直流到12GHz的 [CASCADABLE BROADBAND GaAs MMIC AMPLIFIER DC TO 12GHz]
分类和应用: 放大器
文件页数/大小: 8 页 / 311 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号NBB-312_1的Datasheet PDF文件第1页浏览型号NBB-312_1的Datasheet PDF文件第2页浏览型号NBB-312_1的Datasheet PDF文件第4页浏览型号NBB-312_1的Datasheet PDF文件第5页浏览型号NBB-312_1的Datasheet PDF文件第6页浏览型号NBB-312_1的Datasheet PDF文件第7页浏览型号NBB-312_1的Datasheet PDF文件第8页  
NBB-312  
Pin  
1
Function  
GND  
Description  
Interface Schematic  
Ground connection. For best performance, keep traces physically short  
and connect immediately to ground plane.  
Same as pin 1.  
Same as pin 1.  
2
3
4
GND  
GND  
RF IN  
RF input pin. This pin is NOT internally DC blocked. A DC blocking capacitor,  
suitable for the frequency of operation, should be used in most applica-  
tions. DC coupling of the input is not allowed, because this will override the  
internal feedback loop and cause temperature instability.  
Same as pin 1.  
5
6
7
8
GND  
GND  
GND  
Same as pin 1.  
Same as pin 1.  
RF output and bias pin. Biasing is accomplished with an external series  
resistor and choke inductor to V . The resistor is selected to set the DC  
RF OUT  
CC  
RF OUT  
current into this pin to a desired level. The resistor value is determined by  
the following equation:  
(VCC VDEVICE  
)
R = -------------------------------------------  
ICC  
RF IN  
Care should also be taken in the resistor selection to ensure that the cur-  
rent into the part never exceeds maximum datasheet operating current  
over the planned operating temperature. This means that a resistor  
between the supply and this pin is always required, even if a supply near  
8.0V is available, to provide DC feedback to prevent thermal runaway.  
Alternatively, a constant current supply circuit may be implemented.  
Because DC is present on this pin, a DC blocking capacitor, suitable for the  
frequency of operation, should be used in most applications. The supply  
side of the bias network should also be well bypassed.  
Same as pin 1.  
9
GND  
Package Drawing  
2.94 min  
3.28 max  
0.025 min  
0.125 max  
0.50 nom  
0.50 nom  
1.00 min  
1.50 max  
Pin 1  
Indicator  
Pin 1  
Indicator  
RF OUT  
Ground  
RF IN  
N6  
Ground  
Lid ID  
1.70 min  
1.91 max  
0.98 min  
1.02 max  
0.38 nom  
2.39 min  
2.59 max  
0.37 min  
0.63 max  
All Dimensions in Millimeters  
Notes:  
1. Solder pads are coplanar to within ±0.025 mm.  
2. Lid will be centered relative to frontside metallization with a tolerance of ±0.13 mm.  
3. Mark to include two characters and dot to reference pin 1.  
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical  
support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com.  
Rev A5 DS060124  
3 of 8