DG408, DG409
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25V
Digital Inputs, V
S
, V
D
(Note 3). . . . . .(V-) -2V to (V+) + 2V or 20mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Thermal Information
Thermal Resistance (Typical, Note 4)
JA
(°C/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 125°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC and TSSOP - Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on S
X
, D
X
, EN or A
X
exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
4.
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
DYNAMIC CHARACTERISTICS
Transition Time, t
TRANS
Test Conditions: V+ = +15V, V- = -15V, V
AL
= 0.8V, V
AH
= 2.4V, Unless Otherwise Specified
TEST CONDITIONS
TEMP (°C)
(NOTE 5)
MIN
(NOTE 6)
TYP
(NOTE 5)
MAX
UNITS
(See Figure 1)
(See Figure 3)
(See Figure 2)
Full
25
25
Full
-
10
-
-
-
-
-
-
-
160
-
115
-
105
20
-75
8
3
250
-
150
225
150
-
-
-
-
ns
ns
ns
ns
ns
pC
dB
pF
pF
Break-Before-Make Interval, t
OPEN
Enable Turn-ON Time, t
ON(EN)
Enable Turn-OFF Time, t
OFF(EN)
Charge Injection, Q
OFF Isolation
Logic Input Capacitance, C
IN
Source OFF Capacitance, C
S(OFF)
Drain OFF Capacitance, C
D(OFF)
DG408
DG409
Drain ON Capacitance, C
D(ON)
DG408
DG409
DIGITAL INPUT CHARACTERISTICS
Logic Input Current,
Input Voltage High, I
AH
Logic Input Current,
Input Voltage Low, I
AL
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Drain-Source ON Resistance,
r
DS(ON)
r
DS(ON)
Matching Between Channels,
r
DS(ON)
Source OFF Leakage Current, I
S(OFF)
(See Figure 2)
C
L
= 10nF, V
S
= 0V
V
EN
= 0V, R
L
= 1k,
f = 100kHz (Note 9)
f = 1MHz
V
EN
= 0V, V
S
= 0V,
f = 1MHz
V
EN
= 0V, V
D
= 0V,
f = 1MHz
Full
25
25
25
25
25
25
-
-
-
-
26
14
37
25
-
-
-
-
pF
pF
pF
pF
A
A
V
EN
= 3V, V
D
= 0V,
f = 1MHz, V
A
= 0V or 3V
25
25
V
A
= 2.4V, 15V
V
EN
= 0V, 2.4V,
V
A
= 0V
Full
Full
-10
-10
-
-
10
10
Full
V
D
=
10V,
I
S
= -10mA
(Note 7)
V
D
= 10V, -10V (Note 8)
V
EN
= 0V, V
S
=
10V,
V
D
= +10V
25
Full
25
25
Full
-15
-
-
-
-0.5
-5
-
40
-
-
-
-
15
100
125
15
0.5
5
V
nA
nA
FN3283 Rev 8.00
Jun 13, 2006
Page 4 of 17
RENESAS [ RENESAS TECHNOLOGY CORP ]
