欢迎访问ic37.com |
会员登录 免费注册
发布采购

QT240-ISS-G 参数 Datasheet PDF下载

QT240-ISS-G图片预览
型号: QT240-ISS-G
PDF下载: 下载PDF文件 查看货源
内容描述: 4键的QTouch传感器IC [4 KEY QTOUCH SENSOR IC]
分类和应用: 传感器
文件页数/大小: 12 页 / 258 K
品牌: QUANTUM [ QUANTUM RESEARCH GROUP ]
 浏览型号QT240-ISS-G的Datasheet PDF文件第2页浏览型号QT240-ISS-G的Datasheet PDF文件第3页浏览型号QT240-ISS-G的Datasheet PDF文件第4页浏览型号QT240-ISS-G的Datasheet PDF文件第5页浏览型号QT240-ISS-G的Datasheet PDF文件第7页浏览型号QT240-ISS-G的Datasheet PDF文件第8页浏览型号QT240-ISS-G的Datasheet PDF文件第9页浏览型号QT240-ISS-G的Datasheet PDF文件第10页  
The QT240 will track slow changes in Vdd, but can be
seriously affected by rapid voltage steps.
If the supply is shared with another electronic system, care
should be taken to assure that the supply is free of digital
spikes, sags, and surges which can cause adverse effects.
The supply is best locally regulated using almost any
3-terminal LDO device from 4.0V to 5V.
For proper operation a 0.1µF or greater bypass capacitor
must be used between Vdd and Vss; the bypass cap should
be placed very close to the device Vss and Vdd pins.
The PCB should if possible include a copper pour under and
around the IC, but not extensively under the SNS lines.
spectrum by modulating the oscillator through a resistor to
OSC with a triangle or sawtooth wave.
The modulation signal should be exactly synchronous with
each burst, so that the resulting acquired signal is modulated
in the same way. If this rule is not followed, the signals will
contain modulation noise and false detections may occur.
3.4 UNUSED CHANNELS
Unused SNS pins should not be left open. They should have
a small value non-critical dummy Cs capacitor plus a 2.2K
series-R connected to their SNS pins to allow the internal
circuit to continue to function properly. A nominal value of
1nF (1,000pF) X7R ceramic will suffice.
Unused channels should not have sense traces or
electrodes connected to them except for the required option
resistors, which must always be installed and connected to
Vdd or Vss.
3.3 OSCILLATOR; SPREAD SPECTRUM
The oscillator is an internal type using an external current
bias source. Normal operation occurs at ~100 kHz +/ -20%
with R=62K at Vdd = 4.0V.
In Fast mode the oscillator can be spread-spectrum
modulated with a simple external RC network to avoid
dwelling on any one frequency. The circuit works by current
modulating the oscillator bias to provide a chirp modulation
within each burst. This helps dramatically with both RF
emissions and susceptibility. The circuit for this is shown in
Figure 1-2. The SYNC/SS pin outputs a rectangular pulse
with a period of one burst. At the end of the burst, SYNC/SS
clamps to ground. This forms a sawtooth modulation
waveform to create the frequency chirp modulation (Figure
3-1).
The detection integrator (DI) filters out false detections
caused by interference on up to any 6 of these acquisitions.
The DI is a consensus filter that throws out a pending
detection if even one of the 6 samples does not confirm a
detection. As a result of this feature, it is extremely difficult
for an external signal to interfere with the device.
The typical modulation band of this circuit is +/-7% around
the center frequency.
The oscillator frequency can be measured by observing the
acquisition pulses on any sense channel with an
oscilloscope. The first two positive pulses in each burst will
be exactly 10µs from rising edge to rising edge
(100kHz) if the oscillator is set correctly ( no
spread spectrum). Some subsequent pulse
pairs will have wider spacings; this is normal.
If desired the response time of the device in
Fast mode can be modified by altering the
oscillator frequency. The device can be set to
any center frequency from 20kHz to 150kHz by
simply altering the value of the bias resistor.
Lower values of R will speed up the device.
Higher resistor values will slow down the device
and reduce power consumption.
Slow mode relies on an internal RC timer which
cannot be adjusted via the bias resistor. During
intervals between bursts in Slow mode, the
100kHz oscillator is disabled.
Spread Spectrum in Slow Mode:
The QT240
does not support spread spectrum in Slow
mode directly via the SYNC/SS pin. However,
the designer can still implement spread
3.5 ESD PROTECTION
Normally, only a series resistor is required for ESD
suppression. A 22K Rsns resistor in series with the sense
trace is sufficient in most cases. The dielectric panel (glass
or plastic) usually provides a high degree of isolation to
prevent ESD discharge from reaching the circuit . Rsns
should be placed close to the chip.
If the Cx load is high, Rsns can prevent total charge and
transfer and as a result gain can deteriorate. If a reduction in
Rsns increases gain noticeably, the lower value should be
used. Conversely, increasing the Rsns can result in added
ESD and EMC benefits provided that the increase does not
decrease sensitivity.
3.6 CROSSTALK PRECAUTIONS
Adjacent sense traces might require intervening ground
traces in order to reduce capacitive cross bleed if high
sensitivity is required or high values of delta-Cx are
anticipated (for example, from direct human touch to an
electrode connection). In normal touch applications behind
plastic panels this is almost never a problem regardless of
how the electrodes are wired.
Figure 3-1 Spread-Spectrum Waveforms
lQ
6
QT240R R1.10/0905