4.1 ABSOLUTE MAXIMUM SPECIFICATIONS
Operating temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . as designated by suffix
Storage temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55OC to +125OC
V
DD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to +6.5V
Max continuous pin current, any control or drive pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Short circuit duration to ground, any pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . infinite
Short circuit duration to VDD, any pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . infinite
Voltage forced onto any pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (Vdd + 0.6) Volts
4.2 RECOMMENDED OPERATING CONDITIONS
V
DD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5 to 5.0V
Short-term supply ripple+noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mV
Long-term supply stability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mV
Cs value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10nF to 500nF
Cx value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 100pF
Rs value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470K✡
4.3 AC SPECIFICATIONS
Vdd = 3.0, Cs = 10nF, Rs = 470K, Cx = 10pF, Gain = High, Ta = 20OC, unless otherwise noted.
Parameter
Description
Min
Typ
Max
Units
Notes
T
RC
Recalibration time
550
2
ms
µs
T
Q
Charge, transfer duration
Burst spacing interval
T
BS
75
95
ms
ms
@ 5.0V Vdd
@ 3.3V Vdd
T
BL
Burst length
0.5
3.6
50
ms
ms
kHz
ms
ms
µs
Depends on Cs, Cx
T
R
P
Response time
129
4
F
Piezo drive frequency
Piezo drive duration
Pulse output width on Out
Heartbeat pulse width
Burst frequency
4.4
T
P
75
T
PO
HB
75
T
300
165
F
Q
kHz
4.4 SIGNAL PROCESSING
Vdd = 3.0, Cs = 10nF, Rs = 470K, Cx = 10pF, Gain = High, Ta = 20OC, unless otherwise noted.
Description
Min
Typ
Max
Units
Notes
Threshold differential
6, 12, or 24
counts
%
1
2
Hysteresis
17
4
Detect integrator filter length
Positive drift compensation rate
Negative drift compensation rate
Post-detection recalibration timer duration (typical min/max)
samples
ms/level
ms/level
secs
750
75
4
4
10
60
3, 4
Note 1: Pin options
Note 2: Percentage of signal threshold
Note 3: Pin option
Note 4: Cs, Cx dependent
lq
9
QT118H R1.08 / 0405