4.1 ABSOLUTE MAXIMUM SPECIFICATIONS
Operating temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . as designated by suffix
Storage temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
O
C to +125
O
C
V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to +6.5V
Max continuous pin current, any control or drive pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20mA
.
Short circuit duration to ground, any pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . infinite
.
.
Short circuit duration to V
DD
, any pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . infinite
Voltage forced onto any pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (Vdd + 0.6) Volts
4.2 RECOMMENDED OPERATING CONDITIONS
V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5 to 5.0V
Short-term supply ripple+noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5mV
Long-term supply stability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100mV
Cs value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10nF to 500nF
Cx value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 100pF
Rs value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470K✡
4.3 AC SPECIFICATIONS
Parameter
T
RC
T
Q
T
BS
T
BL
T
R
F
P
T
P
T
PO
T
HB
F
Q
Vdd = 3.0, Cs = 10nF, Rs = 470K, Cx = 10pF, Gain = High, Ta = 20
O
C, unless otherwise noted.
Description
Recalibration time
Charge, transfer duration
Burst spacing interval
Burst length
Response time
Piezo drive frequency
Piezo drive duration
Pulse output width on Out
Heartbeat pulse width
Burst frequency
3.6
0.5
129
4
75
75
300
165
4.4
Min
Typ
550
2
75
95
Max
Units
ms
µs
ms
ms
@ 5.0V Vdd
@ 3.3V Vdd
Notes
50
ms
ms
kHz
ms
ms
µs
kHz
Depends on Cs, Cx
4.4 SIGNAL PROCESSING
Description
Threshold differential
Hysteresis
Detect integrator filter length
Positive drift compensation rate
Negative drift compensation rate
Vdd = 3.0, Cs = 10nF, Rs = 470K, Cx = 10pF, Gain = High, Ta = 20
O
C, unless otherwise noted.
Min
Typ
6, 12, or 24
17
4
750
75
10
60
Max
Units
counts
%
samples
ms/level
ms/level
secs
4
4
3, 4
1
2
Notes
Post-detection recalibration timer duration (typical min/max)
Note 1:
Pin options
Note 2:
Percentage of signal threshold
Note 3:
Pin option
Note 4:
Cs, Cx dependent
lq
9
QT118H R1.08 / 0405