PE42750
Product Specification
Figure 3. Pin Configuration (Top View)
Table 4. Operating Conditions @ 25°C
Parameter
V
DD
Power Supply
I
DD
Power Supply Current
(V
DD
= 3V, V
CNTL
= 3V)
Control Voltage High
Control Voltage Low
P
RF
RF power on RFC,
RF1, RF2 Terminated/
Through 75Ω
T
OP
Operating
Temperature
-40
0.7 x V
DD
0
Min
2.7
Typ
3.0
8
Max
3.63
Unit
V
μA
V
DD
0.3 x V
DD
23/26
+85
V
V
dBm
°C
Operation should be restricted to the limits in the Operating
Ranges table.
Table 5. Absolute Maximum Ratings
Table 3. Pin Descriptions
No.
1
2
3
4
5
6
7
8
9
10
11
12
Pad
Notes: 1.
2.
3.
Parameter/Condition
Description
V
DD
Power supply voltage
V
I
Voltage on CTRL input
P
RF
RF power on RFC, RF1, RF2
Terminated/Through 75Ω
T
ST
Storage temperature
V
ESD
ESD Voltage, HBM,
MIL_STD 883, Method 3015.7
V
ESD
MM ESD Voltage all pins
JEDEC JESD22-A115-A
V
ESD
CDM ESD Voltage
JEDEC JESD22-C101D
Min
-0.3
-0.3
Max
4.0
V
DD
+ 0.3
23/26
Unit
V
V
dBm
°C
Name
GND
RF1
1
GND
GND
RFC
1
GND
GND
RF2
1
RF Ground
RF I/O
RF Ground
RF Ground
RF Common
RF Ground
RF Ground
RF I/O
RF Ground
Control 2 (or logic select)
Control 1 (or logic select)
Supply
Exposed Ground Paddle
-55
+150
2000
150
1000
V
GND
C2
2
C1
2
V
DD
GND
Exceeding absolute maximum ratings may cause permanent
damage. Operation between operating range maximum and
absolute maximum for extended periods may reduce reliability
.
Electrostatic Discharge (ESD) Precautions
When handling this UltraCMOS device, observe the same
precautions that you would use with other ESD-sensitive
devices. Although this device contains circuitry to protect it from
damage due to ESD, precautions should be taken to avoid
exceeding the rating specified.
®
RF pins 2, 5, and 8 must be at 0 VDC. The RF pins do not require
DC blocking capacitors for proper operation if the 0 V DC
requirement is met
Pins 10 and 11 can be set for single pin control
GND must be connected to exposed ground paddle to ensure
good isolation
Table 6. Truth Table
1
V
DD
OFF
2
ON
ON
ON
ON
Note: 1.
2.
Moisture Sensitivity Level
The Moisture Sensitivity Level rating for the PE42750 in
the 12-lead 3 x 3 x 0.75 mm QFN package is MSL1.
C1
Low
Low
Low
High
High
C2
Low
Low
High
Low
High
RFC – RF1 RFC – RF2
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
Switching Frequency
The PE42750 has a maximum 25 kHz switching rate.
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS
devices are immune to latch-up.
Document No. 70-0334-07
│
www.psemi.com
®
A versatile logic table has been established to allow either
C1 or C2 to act as a single pin control and in either polarity
V
DD
at “OFF” represents an all terminated state
©2010-2012 Peregrine Semiconductor Corp. All rights reserved.
Page 3 of 10
PSEMI [ Peregrine Semiconductor ]
