TNY274-280
C5
2.2 nF
250 VAC
L2
D7
Ferrite Bead
3.5 × 7.6 mm
VR1
BYV28-200
T1
+12 V, 1 A
P6KE150A
NC
8
6
J3
J4
C11
100 µF
25 V
C10
1000 µF
25 V
D1
1N4007
F1
D2
R2
1
3
1N4007
100 Ω
RTN
C4
10 nF
1 kV
3.15 A
J1
R1
C1
6.8 µF
400 V
C2
22 µF
400 V
1 kΩ
R7
20 Ω
4
85-265
VAC
RV1
275 VAC
D5
1N4007GP
2
5
D6
UF4003
R5*
3.6 MΩ
J2
D3
1N4007
D4
1N4007
VR2
1N5255B
28 V
L1
1 mH
C6
VR3
BZX79-C11
11 V
1 µF
60 V
R3
47 Ω
1/8 W
*R5 and R8 are optional
components
R6
390 Ω
1/8 W
R8*
21 kΩ
1%
†C7 is configurable to adjust
U1 current limit, see circuit
description
U2
PC817A
D
EN/UV
BP/M
S
S
R4
2 kΩ
1/8 W
C7 †
100 nF
50 V
TinySwitch-III
U1
TNY278P
PI-4244-021406
Figure 14. TNY278P, 12 V, 1 A Universal Input Power Supply.
LED forward drop, current will flow in the optocoupler LED.
This will cause the transistor of the optocoupler to sink current.
When this current exceeds the ENABLE pin threshold current
the next switching cycle is inhibited. When the output voltage
fallsbelowthefeedbackthreshold,aconductioncycleisallowed
to occur and, by adjusting the number of enabled cycles, output
regulation is maintained. As the load reduces, the number of
enabled cycles decreases, lowering the effective switching
frequencyandscalingswitchinglosseswithload. Thisprovides
almost constant efficiency down to very light loads, ideal for
meeting energy efficiency requirements.
Applications Example
The circuit shown in Figure 14 is a low cost, high efficiency,
flyback power supply designed for 12 V, 1 A output from
universal input using the TNY278.
The supply features under-voltage lockout, primary sensed
output overvoltage latching shutdown protection, high
efficiency (>80%), and very low no-load consumption
(<50mWat265VAC). Outputregulationisaccomplishedusing
a simple zener reference and optocoupler feedback.
The rectified and filtered input voltage is applied to the primary
winding of T1. The other side of the transformer primary is
driven by the integrated MOSFET in U1. Diode D5, C2, R1,
R2, and VR1 comprise the clamp circuit, limiting the leakage
inductance turn-off voltage spike on the DRAIN pin to a safe
value. The use of a combination a Zener clamp and parallel
RC optimizes both EMI and energy efficiency. Resistor R2
allows the use of a slow recovery, low cost, rectifier diode by
limiting the reverse current through D5. The selection of a
slow diode also improves efficiency and conducted EMI but
should be a glass passivated type, with a specified recovery
time of ≤2 µs.
As the TinySwitch-III devices are completely self-powered,
there is no requirement for an auxiliary or bias winding on the
transformer. However by adding a bias winding, the output
overvoltage protection feature can be configured, protecting
the load against open feedback loop faults.
When an overvoltage condition occurs, such that bias voltage
exceeds the sum ofVR2 and the BYPASS/MULTIFUNCTION
(BP/M) pinvoltage(28V+5.85V),currentbeginstoflowintothe
BP/Mpin. Whenthiscurrentexceeds5mAtheinternallatching
shutdown circuit in TinySwitch-III is activated. This condition
is reset when the BP/M pin voltage drops below 2.6 V after
removal of the AC input. In the example shown, on opening
the loop, the OVP trips at an output of 17 V.
The output voltage is regulated by the Zener diode VR3. When
theoutputvoltageexceedsthesumoftheZenerandoptocoupler
E
2/06
8