欢迎访问ic37.com |
会员登录 免费注册
发布采购

DP8110 参数 Datasheet PDF下载

DP8110图片预览
型号: DP8110
PDF下载: 下载PDF文件 查看货源
内容描述: 8V至14V输入, 0.7V至5.5V的输出 [8V to 14V Input, 0.7V to 5.5V Output]
分类和应用:
文件页数/大小: 34 页 / 2882 K
品牌: POWER-ONE [ POWER-ONE ]
 浏览型号DP8110的Datasheet PDF文件第1页浏览型号DP8110的Datasheet PDF文件第2页浏览型号DP8110的Datasheet PDF文件第4页浏览型号DP8110的Datasheet PDF文件第5页浏览型号DP8110的Datasheet PDF文件第6页浏览型号DP8110的Datasheet PDF文件第7页浏览型号DP8110的Datasheet PDF文件第8页浏览型号DP8110的Datasheet PDF文件第9页  
DP8110 10A DC-DC Intelligent dPOL Data Sheet
8V to 14V Input
0.7V to 5.5V Output
4.
Electrical Specifications
Specifications apply at the input voltage from 8V to 14V, output load from 0 to 5A, ambient temperature from
-40° to 85°C. Test conditions include an output filter with 2 x 330µF 20m solid electrolytic plus 1 x 22µF X7R
C
ceramic output capacitors, unless otherwise noted.
.
4.1
Input Specifications
Parameter
Input voltage (V
IN
)
Input Current (at no load)
Undervoltage Lockout
VLDO Input Current
V
IN
=14.0V, V
OUT
=3.3V
Ramping Up
Ramping Down
Current drawn from the external low
voltage supply at VLDO=8V
5
50
Conditions/Description
Min
8
50
7.5
Nom
Max
14
Units
VDC
mADC
VDC
VDC
mADC
4.2
Output Specifications
Parameter
Output Voltage Range (V
OUT
)
Output Voltage Setpoint
Resolution
Conditions/Description
Min
0.7
Nom
Max
5.5
2.5mV (1LSB)
2
nd
Units
VDC
Output Voltage Setpoint Accuracy
Output Current (I
OUT
)
Line Regulation
Load Regulation
Dynamic Regulation
Peak Deviation
Settling Time
Output Voltage Peak-to-Peak
Ripple and Noise
Scope BW=20MHz
Full Load
Temperature Coefficient
Switching Frequency
Duty Cycle Limit
2
Vo Loop Enabled
-5.5
2
±(0.6% + 5mV)
7
±0.3
±0.2
50
60
10
20
40
18
35
50
20
500
500 / 1,000
90.5
3.125
100
ADC
%V
OUT
%V
OUT
mV
µs
mV
mV
mV
mV
mV
mV
ppm/°
C
kHz
%
%
V
IN MIN
to V
IN MAX
V
IN MIN
to V
IN MAX
0 to I
OUT MAX
Slew rate 1A/µs, 50 -75% load step
F
SW
=500kHz
to 10% of peak deviation
See Output Load Transient Section
V
IN
=8.0V, V
OUT
=0.7V
V
IN
=8.0V, V
OUT
=2.5V
V
IN
=8.0V, V
OUT
=5.5V
V
IN
=14V, V
OUT
=0.7V
V
IN
=14V, V
OUT
=2.5V
V
IN
=14V, V
OUT
=5.5V
V
IN
=12V, I
OUT
=0.5×I
OUT MAX
Default
Programmable to
Default
Programmable, 1.56% steps
At negative (sink) output current (bus terminator mode) the efficiency of the DP8110 degrades resulting in increased internal power
dissipation and switching noise. Therefore maximum allowable negative current under specific conditions is lower than the current determined
from the de-rating curves shown in paragraph.
BCD.00262 Rev. 1.0, 12 FEB 2013
www.power-one.com
Page 3 of 34