欢迎访问ic37.com |
会员登录 免费注册
发布采购

ADNS-3090 参数 Datasheet PDF下载

ADNS-3090图片预览
型号: ADNS-3090
PDF下载: 下载PDF文件 查看货源
内容描述: 高性能光学鼠标传感器 [High-Performance Optical Mouse Sensor]
分类和应用: 传感器光电二极管
文件页数/大小: 38 页 / 756 K
品牌: PIXART [ PIXART IMAGING INC. ]
 浏览型号ADNS-3090的Datasheet PDF文件第4页浏览型号ADNS-3090的Datasheet PDF文件第5页浏览型号ADNS-3090的Datasheet PDF文件第6页浏览型号ADNS-3090的Datasheet PDF文件第7页浏览型号ADNS-3090的Datasheet PDF文件第9页浏览型号ADNS-3090的Datasheet PDF文件第10页浏览型号ADNS-3090的Datasheet PDF文件第11页浏览型号ADNS-3090的Datasheet PDF文件第12页  
PixArt Imaging Inc.  
ADNS-3090 High-Performance Optical Mouse Sensor  
LP2950ACZ-3.3  
0.1 μF  
3
1
Vin Vo  
0.1  
μF  
0.1  
μF  
4.7  
μF  
GND  
2
4.7  
μF  
Vo  
17  
15  
0.1  
ADNS  
2120  
Lens  
μF  
14  
V DD  
V DD  
Internal  
Image  
HLMP-EG3E  
Vcc  
16  
19  
10  
GND  
Sensor  
Vcc  
Vpp  
187 Ω  
1/8 W  
SURFACE  
16  
GND  
SCLK  
D +  
D +  
D -  
1 KΩ  
5
LED_CTRL  
REFB  
15  
3
MMBT2222A  
21  
D -  
P 0.7  
1.3 KΩ  
11  
2
4
1
22  
23  
24  
GND  
Vreg  
P 1.7  
P 1.5  
P 0.6  
P 0.5  
P 0.4  
MISO  
MOSI  
NCS  
ADNS-3090  
17  
18  
14  
GND  
Vcc  
QA  
QB  
USB  
SHLD  
2.2  
μF  
MCU  
13  
10 KΩ  
10 KΩ  
6
7
REFC  
3
4
P 0.2  
P 0.3  
RESET  
NPD  
240 Ω  
10  
OSC_IN  
9
8
24 MHz  
GUARD  
7
20  
20  
P 1.4  
Ceramic Resonator  
AVX KBR -24.0-MSA  
Murata CSAL24MOX040  
K
K
5
6
OSC_OUT  
Z LED  
Ω
Ω
P 1.0  
P 1.2  
L
Buttons  
M
R
12  
Vo 3.3V  
OPTP  
20  
9
P 1.1  
VSS  
11 18  
20  
XTALOUT  
13  
XTALIN  
12  
Notes:  
All capacitors close to chip  
24 MHz and 6 MHz close to chip  
6 MHz  
(Optional)  
Figure 8. Schematic Diagram for USB, PS/2 mouse application with ADNS-3090  
Notes  
1. Caps for pins 15 and 17 MUST have trace lengths LESS than 5 mm to nearest ground pin.  
2. Pins 15 and 17 caps MUST use pin 16 GND.  
3. Pin 9, if used, should not be connected to PCB GND to reduce potential RF emissions.  
4. The 0.1 uF caps must be ceramic.  
5. Caps should have less than 5 nH of self inductance.  
6. Caps should have less than 0.2 Ω ESR.  
7. NC pins should not be connected to any traces.  
8. Surface mount parts are recommended.  
9. Care must be taken when interfacing a 5V microcontroller to the ADNS-3090. Serial port inputs on the sensor should be connected to open-  
drain outputs from the microcontroller or use an active drive level shifter. NPD and RESET should be connected to 5V microcontroller outputs  
through a resistor divider or other level shifting technique.  
10. VDD3 and GND should have low impedance connections to the power supply.  
11. Capacitors connected to pin 15 and 17 should be connected to pin 16 and then to pin 19.  
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission.  
PixArt Imaging Inc.  
E-mail: fae_service@pixart.com.tw  
8
 复制成功!