欢迎访问ic37.com |
会员登录 免费注册
发布采购

PDA150W-S1A0G-R 参数 Datasheet PDF下载

PDA150W-S1A0G-R图片预览
型号: PDA150W-S1A0G-R
PDF下载: 下载PDF文件 查看货源
内容描述: [150W CONSTANT CURRENT DRIVERS WITH PROVIDE TRULY ADVANCED PERFORMANCE]
分类和应用: 驱动
文件页数/大小: 7 页 / 414 K
品牌: PHIHONG [ PHIHONG USA INC. ]
 浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第1页浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第2页浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第4页浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第5页浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第6页浏览型号PDA150W-S1A0G-R的Datasheet PDF文件第7页  
PDA150W Series  
Brand Name  
Description  
Phihong LED Driver  
150W, 0-10V Isolated Dimming with 20V  
Auxiliary Output for Peripherals  
Input Voltage  
Input Frequency  
Safety  
120 ~ 277VAC  
50/60Hz  
CE, UL, RoHS  
IP66  
IP Rating  
Installation & Application Notes:  
Section I – Physical Characteristics  
1.1  
1.2  
LED Driver shall be installed inside an electrical enclosure.  
Wiring inside electrical enclosure shall comply with 600V/105°C rating or higher.  
Section II – Performance  
2.1  
2.2  
2.3  
2.4  
2.5  
2.6  
2.7  
2.8  
2.9  
2.10  
2.11  
LED Driver complies with UL standard UL8750  
LED Driver has Class A sound rating.  
LED Driver has a minimum ambient operating temperature of -40°C.  
LED Driver has a life expectancy of 50,000 hours at Tcase of 80°C.  
LED Driver has a life expectancy of 100,000 hours at Tcase of 65°C.  
LED Driver has a typical self rise of 25°C at maximum load in open air without heat sink.  
LED Driver maximum allowable case temperature is 80°C – see product label for measurement location.  
LED Driver reduces output power to LEDs if max allowable case temperature is exceeded.  
LED Driver has a failure rate of 0.01% per 1,000 hours at Tcase 70°C.  
LED Driver tolerates sustained open circuit and short circuit output conditions without damage.  
LED Driver complies with the requirements of the Federal Communications Commission (FCC) rules and  
regulations, Title 47 CFR Part 15 Non-Consumer (Class B).  
Section III – UL Conditions of Acceptability (File E321253)  
When installed in the end-use equipment, the following are among the considerations to be made:  
3.1  
The equipment shall be installed in compliance with the enclosure, mounting, spacing, casualty and  
segregation requirements of the ultimate application.  
3.2  
Consideration should be given to measuring the temperatures on electronic components of power circuits  
and transformer windings when the unit is installed in the end-use equipment based upon mounting  
orientation, operating ambient and ventilation.  
3.3  
3.4  
3.5  
These drivers should be used within the recognized ratings.  
The driver is suitable for use in “DAMP” and “DRY” locations.  
The maximum available output parameters from the (0-10V) dimming circuit provided on LED driver model  
PDA150W Series were tested in accordance with supplement (SB) of UL935 and was found  
permissible for connection via Class 2 wiring.  
3.6  
3.7  
When the drivers are installed in the end-use application, the case temperature should not exceed the  
temperature limit specified.  
The maximum measured leakage current was 0.2mA while connected to a 277V source of supply.  
PHIHONG TECHNOLOGY CO., LTD.  
47800 Fremont Blvd., Fremont, CA 94538 • T: 1-510-445-0100 • www.phihong.com/LED  
Revision 7/2/2014