页页次: 5/10
详细说明
该RS7215是一个低压差线性稳压器。该器件可提供预设的1.8V,2.5V和3.3V输出电压的输出
电流可达1.0A 。可调输出电压和特殊的输出电压等面膜的选择也可以。如
在功能块图所示,它由1.175V带隙(固定电压型0.95V )的参考,错误
放大器,一个P沟道传输晶体管和一个内部反馈电压分压器。
对于固定电压的类型的带隙基准是连接到误差放大器,该放大器与比较该参考
反馈电压,并且放大电压差。如果反馈电压低于基准电压时,所述密码
晶体管的栅极被拉低,允许更多的电流传递到输出引脚,并增加输出电压。如果
反馈电压过高时,传输晶体管栅极被拉起以降低输出电压。
输出电压反馈通过一个内部电阻分压器(或外部电阻分压器,用于调节输出
电压型)连接到V
OUT
引脚。附加块包括输出限流器,热传感器,并关断逻辑。
内部P沟道MOSFET
该RS7215拥有一个P沟道MOSFET晶体管。不像使用PNP调整晶体管类似的设计时,P沟道
MOSFET的不需要基极驱动,从而降低了静态电流。 PNP型监管机构也浪费了相当大的电流
dropout when the pass transistor saturates, and use high base‐drive currents under large loads. The RS7215 does not suffer
这些问题,仅消耗60μA (典型值)电流消耗在重负载下,以及在降
条件。
使能功能
EN引脚启动以及停止稳压器。当EN引脚被切换到关闭电源电平,所有内部电路的动作
停止时,引脚V的积聚在P沟道MOSFET输出晶体管
IN
和V
OUT
关闭时,允许电流
消耗大幅度减少。在V
OUT
销进入到V之间的内部放电路径的GND电平
OUT
和GND引脚。
快速放电功能
该RS7215固定式对EN引脚禁用快速放电功能。当用户关闭该设备,其内部上拉低
电阻会放电输出电容充电。这将避免出现错误的议案等设备。
输出电压选择
For fixed voltage type of RS7215, the output voltage is preset at an internally trimmed voltage. The first two digits of part
number suffix identify the output voltage (see Ordering Information). For example, the RS7215‐33 has a preset 3.3V output
电压“。
For adjustable voltage type of RS7215, the output voltage is set by comparing the feedback voltage at adjust terminal to the
内部带隙基准电压。参考电压V
REF
为1.175V 。输出电压由下式给出:
V
OUT
=
V
REF
× ⎜
1
+
⎝
⎛
R1
⎞
⎟
R2
⎠
电流限制
The RS7215 also includes a fold back current limiter. It monitors and controls the pass transistor’s gate voltage, estimates the
output current, and limits the output current within 1.3A.
热过载保护
Thermal overload protection limits total power dissipation in the RS7215. When the junction temperature exceeds T
J
=+150°C,
热传感器关断导通晶体管,使IC降温。热传感器接通传输晶体管
again after the junction temperature cools down by 20°C, resulting in a pulsed output during continuous thermal overload
条件。
Thermal overload protection is designed to protect the RS7215 in the event of fault conditions. For continuous operation, the
的T绝对最大工作结温额定值
J
=+125°C should not be exceeded.
DS‐RS7215‐02
September, 2009
www.Orister.com