MC10102
PACKAGE DIMENSIONS
PLCC–20
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
M
S
S
0.007 (0.180)
T
L-M
N
B
Y BRK
–M–
–N–
M
S
S
N
0.007 (0.180)
T
L-M
U
D
D
–L–
Z
W
20
1
S
S
S
0.010 (0.250)
T
L-M
N
G1
X
V
A
VIEW D–D
M
M
S
S
S
S
0.007 (0.180)
0.007 (0.180)
T
L-M
L-M
N
N
M
S
S
N
0.007 (0.180)
T
L-M
H
Z
T
R
K1
K
C
E
M
S
S
N
0.007 (0.180)
T
L-M
F
0.004 (0.100)
VIEW S
G
–T– SEATING
PLANE
J
VIEW S
NOTES:
INCHES
MILLIMETERS
G1
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
DIM MIN
MAX
0.395
0.395
0.180
0.110
0.019
MIN
9.78
9.78
4.20
2.29
0.33
MAX
10.03
10.03
4.57
S
S
S
0.010 (0.250)
T
L-M
N
A
B
C
E
F
0.385
0.385
0.165
0.090
0.013
2.79
0.48
G
H
J
0.050 BSC
1.27 BSC
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
0.026
0.020
0.025
0.350
0.350
0.042
0.042
0.042
---
0.032
---
---
0.66
0.51
0.64
8.89
8.89
1.07
1.07
1.07
---
2
0.81
---
---
9.04
9.04
1.21
1.21
1.42
0.50
10
K
R
U
V
W
X
Y
Z
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
0.356
0.356
0.048
0.048
0.056
0.020
10
2
_
_
_
_
G1 0.310
K1 0.040
0.330
---
7.88
1.02
8.38
---
http://onsemi.com
4
ONSEMI [ ONSEMI ]
